IKEA LAGAN Manual De Instrucciones página 7

EN
Plate position-beneath framed recessed cabinet
bottom
NOTE:
READ IT IS VERY IMPOR
IN THE AND FOLLO TANT TO
BEFOR INSTA LLATIO W THE DIREC
REAR E PROCE N INSTR TIONS
WALL TEMPL EDING WITH THIS UCTIO NS
This Rear Wall Template ATE. 3/8" TO EDGE
mounting plate and serves 12"
outlet. 1. Use to locate the horizonta to position the bottom
accuratel a level to check l exhaust
2. Locate y. that the template
right side and mark at least is positione d
of the centerline one stud on the left 4"
screw mounted It is important to use at . or
of the microwav firmly in a stud to least one
locations for the supplied e. Mark two additiona support the weight wood
3. Drill holes in the marked toggle bolts. l, evenly
a stud, drill a 3/16" locations. spaced
that do not line hole for wood screws. Where there is
toggle bolts. up with a stud, drill 5/8" For holes
AT THIS DO NOT INSTALL holes for
4. Remove TIME. THE MOUNTIN
5. Review the template G PLATE
installatio the Installatio n Instructio from the rear wall.
n situation. n book
for your
Darle vuelta
versión a la hoja
en Español. para consulta r la
Locate and mark
mounti holes to
IMPOR ng plate. align with holes in
TANT: the
LOCAT E AT LEAST
THE CENTE ONE STUD
MARK RLINE ON EITHE
THE LOCAT . R SIDE
SPACE D TOGG ION FOR OF
AREA. LE BOLTS 2 ADDIT IONAL
IN THE MOUN , EVENL Y
TING PLATE
Trim the
rear wall
templa te along
the dotted
line.
Locate
mounti
IMPOR
LOCAT
THE CENTE
MARK
SPACE
AREA.
C
Draw a vertical line on the wall at the center of the 30"
space.
Tape the Rear Wall Template onto the wall matching the
centerline and touching the bottom cabinet frame.
D. ALIGNING THE WALL PLATE
1. Draw a vertical line on the wall at the center of the 30"
wide space.
2. Draw a horizontal line on the wall at the bottom of
"Rear Wall Template".
3. Find a wall stud in area "E" of mounting plate Refer to
section 1B. Finding the wall studs.
4. For attaching the mounting plate into stud drill a 3/16"
hole into wood stud. Drill a 5/8" hole for toggle bolt in
1 other location (Hole A or Hole B)
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.
1/4"
Minimum
clearance
Trim the
rear wall templa
te along
the dotted
line.
and mark
ng plate. holes to align with
holes in
TANT: the
E AT LEAST
ONE STUD
RLINE . ON EITHE
THE LOCAT R SIDE OF
D TOGG ION FOR 2 ADDIT
LE BOLTS IONAL
IN THE MOUN , EVENL Y
TING PLATE
30" to Cooktop
Hole B
Horizontal Line
Area E
Your cabinets may have decorative trim that interferes
with the microwave installation. Remove the decorative
trim to install the microwave properly and to make it
level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a or front filler piece. only, with no
back or side frame, install the mounting plate down the
same distance as the front overhang or front filler piece
thickness. This will keep the microwave level.
1. Measure the inside depth of the or front filler piece.
2. Draw a horizontal line on the back wall an equal dis-
tance below the cabinet bottom as the inside depth of
the or front filler piece.
3. For this type of installation with front overhang only,
align the mounting tabs with this horizontal line, not
touching the cabinet bottom as described in Step D.
REAR WALL TEMPLATE
Centerline
Draw a Vertical Line
notches
on Wall from Center
of Top Cabinet
Draw a horizontal line on
wall at the bottom of "Rear
Wall Template".
NOTE: Holes A and B are inside area E. If neither of Holes
A and B are not in a stud, find a stud somewhere in area
E and draw a circle to line up with the stud. It is impor-
tant to have at least one wood screw mounted firmly
in a stud to support the weight of the microwave. Set
the mounting plate aside.
Hole A Horizontal Line
7