IKEA LAGAN Manual De Instrucciones página 14

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
DUCT PIECES
Equivalent lengths of duct pieces are based on actual tests and reflect
requirements for good venting performance with any vent hood.
* IMPORTANT: For back exhaust, care should be taken to align exhaust with space between studs, or wall
should be prepared at the time it is constructed by leaving enough space between the wall studs to accommo-
date exhaust.
B OUTSIDE BACK EXHAUST
Duct)
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
• Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
• Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
3/8" TO EDGE
12"
TO
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE. 4"
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet. 1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
4. Remove the template AT THIS TIME. from the rear wall.
e Installation Instruction book for your
5. Revie installation situation. w h t
para consultar la
Darle vuelta a la hoja
versión en Español.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT: STUD ON EITHER SIDE OF
LOCATE AT LEAST ONE
THE CENTERLINE. FOR 2 ADDITIONAL, EVENLY
MARK THE LOCATION IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA. Locate and mark holes
m o u t n g n i l p t a . e
IMPORTANT: LOCATE AT LEAST ONE
THE CENTERLINE.
MARK THE LOCATION
Trim the rear wall template along the dotted line. SPACED TOGGLE BOLTS
AREA.
14
Wall Cap
3 Ft. Straight Duct
(3 ⁄ " x 10"/8.2 x 25.4
1
4
cm Rectangular)
90° Elbow
(Horizontal
along the dotted line.
Trim the rear wall template
to align with holes in the
STUD ON EITHER SIDE OF
FOR 2 ADDITIONAL, EVENLY
IN THE MOUNTING PLATE
IMPORTANT :Do not remove the
cardboard spacers between the
heat shield and door.
EQUIVALENT
LENGTH x
40 Ft. (12.2 m) x
3 Ft. (0.9 m) x
10 Ft. (3 m) x
B1. PREPARING THE REAR WALL FOR OUTSIDE
BACK EXHAUST
You need to cut an opening in the rear wall for outside
exhaust.
• Read the instructions on the REAR WALL TEMPLATE.
• Tape it to the rear wall.
• Cut the opening, following the instructions of the REAR
WALL TEMPLATE.
NUMBER EQUIVALENT
USED = LENGTH
(1) = 40 Ft. (12.2 m)
(1) = 3 Ft. (0.9 m)
(2) = 10 Ft. (3 m)
Total Length = 63 Ft. (19.2 m)
EN