IKEA RAGLANDA Manual Del Usuario página 14

ENGLISH
What to do if ...
In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following
list. For other errors or issues please contact authorized After-sales Service which contact details can be found in
the guarantee booklet. Spare parts will be available for a period of either up to 7 or up to 10 years, according to the
specific Regulation requirements.
The spare parts can be found: https://parts-selfservice.whirlpool.com/en/landing
Problems... Possible causes...
Salt reservoir is empty. (After refill the salt
Salt indicator
indicator may remain lit for several wash
is lit
cycles).
Rinse aid dispenser is empty. (After refill
Rinse aid
the rinse aid indicator may remain lit for
indicator is lit
several wash cycles).
The appliance has not been plugged in
properly.
Power outage.
The dishwasher
The dishwasher door is not closed.
won't start or
NATURALDRY pin is not pulled in.
does not respond
Cycle is interupted by door opening for
to commands.
more than 4 seconds.
It does not respond to commands.
Display shows: 9 or 12 and On/Off LED is
blinking rapidly
The dishwasher
The wash cycle has not finished yet.
won't drain.
The drain hose is bent.
Display shows:
3 and On/Off
The sink drain pipe is blocked.
LED is blinking
The filter is clogged up with food residues.
rapidly
The dishes are rattling against each
The dishwasher
makes excessive
An excessive amount of foam has been
noise.
produced.
The crockery has not been arranged
properly.
The spray arms cannot rotate freely, being
hindered by the dishes.
The wash cycle is too gentle and/or
detergent efficiency is low.
The dishes are
not clean.
An excessive amount of foam has been
produced.
The cap on the rinse aid compartment has
not been shut correctly.
The filter is soiled or clogged.
There is no salt.
Dishwasher
finishes the cycle
Drain hose positioned too low or siphoning
prematurely.
into home sewage system.
Display shows:
15 and On/Off
LED is blinking
Air in water supply.
rapidly
Solutions...
Refill reservoir with salt (for more information - see page 8).
Adjust water hardness - see table, page 8.
Refill dispenser with rinse aid (for more information - see page 8).
Insert the plug into the socket.
For safety reasons, dishwasher will not re-start automatically when
power returns. Open dishwasher door, press START/Pause button
and close the door within 4 seconds.
Vigorously push the door until you hear the "click".
Press START/Pause and close the door within 4 seconds.
Switch off the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and restart the program.
If problem persists, unplug the appliance for 1 minute, then plug it
back in.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALLATION).
Clean the sink drain pipe.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER). Restart the current cycle by switching OFF the
dishwasher, then switch it on again, select a new program, press
START/Pause and close the door within 4 seconds. Please do not
add any detergent.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suita-
ble for use in dishwashers (see FILLING THE DETERGENT DISPENSER).
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CLEANING AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Check if end of drain hose is placed at correct height (see
INSTALLATION). Check for siphoning into home sewage system,
install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
14