Chasing M2 PRO MAX Manual Del Usuario página 9

4
Thruster/ Propeller
After use, you need to clean the attachments on the surface of the motor rotor
(Please make sure that the device is completely turned off to avoid personal
injury). Rinse with clean water, and wipe with a towel after cleaning.
EN
Do not touch the
propellers of the Thruster
Note: We strongly recommend that you soak the ROV body in fresh water for at least
1 hour after you use the ROV in seawater, and run the motor for 10 minutes. After
cleaning, wipe the ROV with a cleaning cloth.
5
Tether socket/Peripheral socket/Micro SD card socket
 Before use, check whether the sealing covers of the peripheral socket and micro
SD card socket are installed in place. You can tighten the cover with the help of a flat
wrench or a coin. In addition, you need to check whether the tether connector
sockets are dry and clean.
 Salt and moisture may lead to socket corrosion. If any water droplet enter the
socket, make sure to rinse the socket with clean water, and absorb the water in the
socket with a paper towel or cotton balls.
 After use, please always clean the peripheral socket and the tether socket, and
tighten the sealing cover.
6 O-ring
· Check whether the O-ring on the tether connector/Battery socket/micro SD card
socket pre-dive, and make a replacement when it is missed or damaged.
· It is recommended to grease the o-ring at the interface seal for maintenance each
time when the battery cabin and micro SD card are removed and installed
7 E-Reel
· You need to wait 4 seconds when you turn on the power for the first time and
rotate the speed knob to slow/fast gear.
· When there is explosion wire, you should turn off the power immediately,
finishing after getting tether organized.
· When the winding is almost complete, please adjust to a slow speed in advance.
After winding up, please timely adjust to the closing gear and turn off the power.
· Check if the O-rings on the tether connectors are dropped or damaged. If there
are missing or damaged, please replace them in time.
· Please pay attention to hold the E-Reel in the process of wire winding up or down.
· E-Reel supports IP65 class waterproofing. Do not put the E-Reel in the water or
splash liquid on it. E-Reel water damage is out of warranty.
15
Do not unlock the Thruster for more than 30
seconds in the air to avoid overheating
8 Other
1. Do not turn on the LED lights before entering the water to avoid damages.
2. Check if the Thrusters/propellers are getting stuck by seaweed or external matters,
rinse the ROV with fresh water and then dry and put it back in the packing box.
3. Remote control cannot be washed with water, please clean it with towel.
4. The pull ring at the end of the battery can only be used to remove the battery, not to
lift the ROV, otherwise it may damage the ROV.
5. Do not place heavy objects on drone or accessories to avoid possible damage.
6. People under the age of 16 should only use this drone under adult supervision.
7. When not in use, please do not expose the drone and accessories under \
sunlight. Store it in a cool place or in a special box.
8. Chloride or other chemicals can erode Chasing M2 PRO. Do not use if the pool
is under high chlorine level.
9. Before you remove the battery compartment, make sure to unlock the buckle for
the battery compartment. If you lift the battery compartment by using excessive
force, the battery compartment may be damaged, and this damage falls out of the
scope of the after-sales warranty.
Support
If you have any questions or technical issues, send an email to the aftersales services of
Chasing or contact us on the official website.
Aftersales support on the official website: https://www.chasing.com/ >> Contact us >>
Aftersales service email addresses:
support01@chasing-innovation.com for Europe,support02@chasing-innovation.com for Asia
and Oceania,and support03@chasing-innovation.com for South America,North America,
and Africa.
This guide may be updated without notice.
Visit the Chasing official website for the latest version: https://www.chasing.com
Online Customer Support >>Click here
EN
16