Specific Safety Rules - Ridgid R4092 Manual Del Operador

GENERAL SAFETY RULES
 INSPECT EXTENSION CORDS PERIODICALLY and replace
if damaged.
 GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole electrical
receptacle.
 ONLY POWER THE TOOL WITH A GFCI (GROUND FAULT
CIRCUIT INTERRUPTOR) PROTECTED OUTLET.
 CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely
understood or if in doubt as to whether the tool is properly
grounded.
 USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool's plug.
 DO NOT MODIFY the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
 STAY ALERT AND EXERCISE CONTROL. Watch what you
are doing and use common sense. Do not operate tool when
you are tired. Do not rush.

SPECIFIC SAFETY RULES

 SECURE WORK firmly against the miter guide or fence.
 NEVER stand or have any part of your body in line with the
path of the wheel.
 NEVER attempt to free a stalled wheel without first turning
the saw OFF and disconnecting the saw from the power
source.
 IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
 AVOID AWKWARD OPERATIONS AND HAND POSITIONS
where a sudden slip could cause your hand to move into
the cutting tool.
 MAKE SURE THE WORK AREA HAS AMPLE
LIGHTING to see the work and that no obstructions will
interfere with safe operation BEFORE performing any work
using the saw.
 ALWAYS TURN OFF SAW before disconnecting it, to avoid
accidental starting when reconnecting to power supply.
 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON
AND OFF. Have defective switches replaced by an authorized
service center.
 USE ONLY CORRECT WHEELS. Do not use wheels with
incorrect size holes. Never use washers or arbor nuts that
are defective or incorrect. The maximum wheel capacity of
your saw is 10 in. (254 mm).
 BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS
ARE SECURE.
 NEVER TOUCH WHEEL or other moving parts during use.
 NEVER START A TOOL WHEN ANY ROTATING
COMPONENT IS IN CONTACT WITH THE WORKPIECE.
 DO NOT OPERATE A TOOL WHILE UNDER THE INFLUENCE
OF DRUGS, ALCOHOL, OR ANY MEDICATION.
 WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause product
damage.
 USE ONLY RECOMMENDED ACCESSORIES listed in this
manual or addendums. Use of accessories that are not listed
may cause the risk of personal injury. Instructions for safe
use of accessories are included with the accessory.
 DOUBLE CHECK ALL SETUPS. Make sure wheel is tight
and not making contact with saw or workpiece before
connecting to power supply.
 THIS TOOL should have the following markings:
a) To reduce the risk of injury, the user must read and
understand operator's manual.
b) Wear eye, hearing, and respiratory protection when
operating the tool.
c) Do not remove the wheel guard.
d) Do not stack or store tiles on water trays.
e) Never operate the tool without the wheel guard securely
closed.
f) Turn off tool, wait for the wheel to stop moving, and
disconnect the power to the tool before servicing, when
changing cutting wheels, or cleaning.
g) Never use wheels that have openings, grooves, or teeth
on this tool.
h) Always inspect and replace damaged cutting wheels
before operating the tool.
i) Do not expose to rain or other damp locations.
j) Do not fill water bath above maximum water fill line.
 SAVE THESE INSTRUCTIONS. Refer to them frequently
and use to instruct other users. If you loan someone this
tool, loan them these instructions too.
4 — English