Tabla De Contenido - Textron Jacobsen Ar250 Serie Manual De Seguridad Y Funcionamiento

1 CONTENTS
CONTENTS
2 INTRODUCTION
2.1 IMPORTANT .............................................................. 2
2.2 PRODUCT IDENTIFICATION ....................................... 2
2.3 GUIDELINES FOR THE DISPOSAL OF SCRAP
PRODUCTS ............................................................... 2
2.3.1 DURING SERVICE LIFE .............................................. 2
2.3.2 END OF SERVICE LIFE ............................................... 2
3 SAFETY INSTRUCTIONS
3.1 OPERATING INSTRUCTIONS ..................................... 4
3.2 SAFETY SIGNS .......................................................... 4
3.3 STARTING THE ENGINE ............................................. 4
3.4 DRIVING THE MACHINE ............................................ 4
3.5 TRANSPORTING ........................................................ 4
3.6 LEAVING THE DRIVING POSITION ............................ 5
3.7 SLOPES ..................................................................... 5
3.8 BLOCKED CUTTING CYLINDERS .............................. 5
3.9 ADJUSTMENTS, LUBRICATION AND
MAINTENANCE ......................................................... 5
4 SPECIFICATIONS
4.1 ENGINE SPECIFICATION ............................................ 7
4.2 MACHINE SPECIFICATION ........................................ 7
4.3 DIMENSIONS ............................................................. 7
4.4 VIBRATION LEVEL .................................................... 7
4.5 SLOPES ..................................................................... 7
4.6 CUTTING UNIT SPECIFICATION ................................ 8
4.7 RECOMMENDED LUBRICANTS ................................. 8
4.8 CUTTING PERFORMANCE (AREA) ............................ 8
4.9 CONFORMITY CERTIFICATES .................................. 9
5 DECALS
5.1 SAFETY DECALS ..................................................... 11
5.2 INSTRUCTION DECALS ............................................ 11
6 CONTROLS
6.1 STARTER KEY SWITCH ............................................ 12
6.2 THROTTLE CONTROL LEVER .................................. 12
6.3 STEERING WHEEL RAKE ADJUSTMENT .................. 12
6.4 TRACTION FOOT PEDAL ......................................... 12
6.5 NEUTRAL LATCH (B) ............................................... 12
6.6 SPEED LIMITER ....................................................... 13
6.7 PARK BRAKES .......................................................... 13
6.8 HYDRAULIC LIFT LEVER ......................................... 13
6.9 UNIT COUNTERBALANCE CONTROL ....................... 14
6.10 CUTTING UNIT SWITCHES ....................................... 14
6.11 UNIT TRANSPORT STOP ......................................... 15
6.12 INSTRUMENT PANEL ............................................... 15
6.13 HOURMETER ............................................................ 16
6.14 BONNET RELEASE KEY ............................................ 16
7 OPERATION
7.1 DAILY INSPECTION .................................................. 17
7.2 OPERATOR PRESENCE AND SAFETY INTERLOCK
SYSTEM ................................................................... 18
7.3 OPERATING PROCEDURE ......................................... 19
7.4 STARTING THE ENGINE ............................................ 20
7.5 DRIVING ................................................................... 20
7.6 MOWING .................................................................. 21
7.7 TO STOP THE ENGINE .............................................. 21
7.8 PUSHING THE MACHINE WITH THE ENGINE
STOPPED ................................................................. 21
SAFETY AND OPERATORS MANUAL
PAGE CONTENTS
8 ADJUSTMENTS
8.1 HEIGHT OF CUT ....................................................... 22
8.2 GENERAL INSTRUCTIONS FOR GRAMMER SEATS . 23
8.3 SEAT (Grammer GS85/90) ...................................... 25
8.4 AIR SUSPENSION SEAT (Grammer MSG75 -521) .. 26
8.4.1 WEIGHT ADJUSTMENT ............................................ 26
8.4.2 FORE/AFT ADJUSTMENT ......................................... 26
8.4.4 SEAT HEATER ........................................................... 27
8.4.5 LUMBAR SUPPORT ................................................. 27
8.4.3 BACKREST EXTENSION ........................................... 27
8.4.6 ARMRESTS .............................................................. 28
8.4.7 ARMREST ADJUSTMENT ........................................ 28
8.4.8 BACKREST ADJUSTMENT ....................................... 28
8.4.9 MAINTENANCE ........................................................ 29
9 MAINTENANCE
9.1 LUBRICATION AND MAINTENANCE CHART ............ 30
9.2 DAILY CHECKS (Every 8 working hours) ............. 32
10 GUARANTEE / SALES & SERVICE ............................ 33
JACOBSEN AR250 Series CE
PAGE
GB-1