Important - Poggio Solutions R180 Instrucciones Originales

EN OPERATING INSTRUCTIONS
• Connect the cigarette lighter cable to the cigarette
lighter socket and to the compressor (fig . C1, fig . C2, fig .
C3)
• After setting the switch
use the compressor directly .
IMPORTANT: take care not to discharge your vehicle's
battery . You can start your engine when using the
compressor (in an open area to avoid the risk of
poisoning) .
• After turning the switch
unplug your compressor .
10. AUTOMATIC ANGLED CONNECTOR
The automatic connector
allows the compressor to be easily connected to a
PRESTA type valve (with or without extension) or a
SCHRADER type valve . It is located in one of the pockets
of the transport bag .
Its ergonomics are particularly well adapted to the
lenticular solid wheels . It holds in place by itself, even if
there is a lot of pressure .
For a better ease of use we advise you to place the valve
towards the bottom of the wheel .
IMPORTANT: this nozzle is a new process . It is advisable
to carry out tests to have an optimum grip of the device .
Never force .
- Screw the connector onto the air hose (fig . J1)
and lock it (fig . J2) .
a) Adjustment for PRESTA or SCHRADER valve (fig. J3)
1 . Take out the ring
2 . Turn the selector switch to match the mark with P
(Presta) or S (Schrader) .
3 . Push the ring back in before use
b) Fitting the inflation connector (fig. J4)
1 . Press the connector firmly onto the valve
2 . Then slide the red ring all the way down
3 . Screw on the ring, without forcing, to lock
4 . Once inflation is complete, remove the connector by
holding it by the ring, without unscrewing it .
26
to the ON position, you can
2
to the OFF position, you can
2
, supplied with the R180,
11b
11. USE OF THE SCREW CONNECTOR
The R180 is equipped with a reversible screw connector
for PRESTA or SCHRADER type valves . This connector
11
is intended for valves that do not fit the automatic
connector or are difficult to access .
b) Assembly for SCHRADER valves
1 . Screw the connector onto the pipe on the «PRESTA»
side (fig . I1) and tighten it firmly .
2 . Then screw the connector onto the valve (Fig . I2) until it
locks (Fig . I3) .
b) Assembly for PRESTA valves
1 . Screw the connector onto the pipe on the «SCHRADER»
side (fig . I4) and lock it firmly .
2 . Then screw the connector onto the valve (Fig . I5) until it
locks (Fig . I6) .
12. OTHER INFLATION ACCESSORIES
The R180 is delivered with 3 nozzle
in the transport bag
• They are intended for various types of accessories,
balls or inflatable toys (fig . J1, fig . J2, fig . J3) .
• These nozzle are screwed onto the connector
PRESTA side (fig . J4)
• You can screw other types of inflation fittings with an
M 11 thread directly onto the hose or onto the screw
connector . Make sure that these accessories are used
as intended and comply with the conditions of use as
described in the chapter «Safety instructions» .
13. USING THE CLIP-ON BIKE MOUNT
The R180 has a retractable bike mount that allows you to
transform your compressor into a stand for a road bike
(up to 9 kg)
• Unclip the metal support
compressor (fig . J1)
• Slide the support into the slot on the top of the
compressor (fig . J2)
• Place the rear wheel of your bicycle on the support (fig .
J3)
• After use, you can remove the holder and place it in its
housing under the compressor (magnetic holder) (fig .
K4) .
which are
12 13 14
on the
11
located under the
10