WERKU WK401450 Manual De Instrucciones página 5

ENG ORIGINAL INSTRUCTIONS
electrical polarity, which can be solved by simply
removing the plug from the power tool and reinser-
ting it backwards. To disconnect, turn off the power
tool and move the switch to the "O" position (17).
CONNECTING TO A POWER TOOL DUST
EXTRACTION OUTLET.
If you connect the vacuum cleaner to a power tool
using the hose of this vacuum cleaner, insert the
nozzle (11) into the extraction outlet of the power
tool. If the nozzle does not fit, use the 26, 32, 35 or
45 mm adapter (18). The adapter may need to be
cut to fit the power tool's extraction outlet. If con-
necting the vacuum cleaner to a power tool using
the hose of said power tool, place the adapter (19)
on the hose outlet of the power tool and insert it
into the suction inlet of the vacuum cleaner.
HEPA FILTER AND SPONGE FILTER.
Important. This vacuum cleaner has two filters, a
HEPA filter and a sponge filter. The HEPA filter is
only for dry vacuuming. The sponge filter is only
for wet vacuuming. It is essential that one of these
filters is mounted, according to the corresponding
use.
FILTER ASSEMBLY.
For both the HEPA filter assembly and the spon-
ge filter assembly, loosen the retaining straps, re-
move the body of this vacuum cleaner and turn
it around to access the parts (14).Remove the fil-
ter from its support guide (15). Clean it with soap
and water. Before reinstall it, let it dry completely.
Periodic cleaning of the HEPA filter is very impor-
tant in order to prevent dust from being expelled
through the grilles.
EMPTYING DEPOSIT.
If liquid has been sucked, the tank must be over-
turned before it can be emptied by gravity.
CLEANING CYCLE.
At each hour of use, or if you feel the suction drops,
press the cleaning button 4 or 5 times to recover
all the suction (12).
FILTER BAG.
To change it, lift the top cover and place it on its
support (13).
CLEANING LINK PIPE.
To access the pipes, release the clamping bands.
Remove the body of this vacuum cleaner and turn
it half a turn to access the parts (14). Manually di-
sassemble the duct and clean it with tap water (16).
FILLING WATER TANK.
To access the tank, release the clamping straps
and remove this vacuum cleaner body (14). Fill
the tank with clean water.
CLEANING FILTER BAG.
When the bag is full, lift the top cover, take the bag
out of its guide by the mouth and empty the dust
by opening the bottom of the bag. Close the bag
and install it again for a new use.
EMPTYING WATER.
Move this vacuum cleaner to a drain. Release the
clamping straps. Remove the body of this vacuum
cleaner and turn the container half a turn to empty
the water. Clean the container with clean water.
DRY ASPIRATION.
Do not aspirate toxic or dangerous substances
such as asbestos or toxic metallic dust. Refer to
the safety data sheet of the material to be aspira-
ted in case of doubt. The filters may not be able
to catch all the particles and release them into the
environment. Before use this vacuum cleaner to
extract dry materials, it must be configured for dry
material extraction. The pair of main corrugated fil-
ters and the diaphragm filter must always be mou-
nted. Note: Dry suction is not recommended when
there is liquid in the reservoir or reservoir and fil-
ters are still damp. Severe dust solidification may
occur which can cause damage to this vacuum
cleaner. Whenever you move from wet to dry suc-
tion make sure that the reservoir and filter system
is completely clean and dry. If it is necessary to
change frequently between dry and wet suction it
is better to have two main filter sets.
LIQUID ASPIRATION.
Never vacuum corrosive or flammable liquids.
Caution: Never start wet vacuuming when there is
dry powder in the tank, as dangerous dust coagu-
lation and possible damage to this vacuum cleaner
could occur. Always clean the tank before starting.
5
English