WERKU WK401450 Manual De Instrucciones página 3

ENG ORIGINAL INSTRUCTIONS
ses will reduce the risk of electric shock. Avoid
body contact with grounded surfaces such as pi-
pes, radiators, cookers and refrigerators. There is
an increased risk of electric shock if your body is
grounded. Do not expose power tools to rain or
wet conditions. Water entering this power tool will
increase the risk of electric shock
DO NOT ABUSE CORD.
Never use the cord to carry, lift or unplug this power
tool. Keep the cord away from heat, oil, sharp ed-
ges or moving parts. Damaged or entangled cords
increase the risk of electric shock. When operating
this power tool outdoors, use an extension cord
suitable for outdoor use. The use of an extension
cord suitable for outdoor use reduces the risk of
electric shock. If the use of this power tool in a
damp location is unavoidable, use a power protec-
ted by a residual current device (RCD). The use of
an RCD reduces the risk of electric shock.
AVOID ACCIDENTAL STARTING.
Make sure the switch is in "off" position before
connecting to the network, or when taking or ca-
rrying this power tool. Carrying power tools with
your finger on the switch or plugging in power tools
that have the switch in "on" position invites to ac-
cidents. Remove keys or tools before starting this
power tool. A left key or tool attached to a rotating
part of this power tool can cause personal injury.
USE AND CARE.
Do not force this power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it
was conceived. Do not use this power tool if the
switch cannot be positioned to "off" and "on" posi-
tion. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
Remove the plug from the power supply and/or
battery before making any adjustments, changing
accessories or storing this power tool. Such pre-
ventive safety measures reduce the risk of starting
this power tool accidentally.
STORAGE.
Store power tools out of reach of children and do not
allow the handling of power tools to people unfami-
liar with the tools or these instructions. Power tools
are dangerous in the hands of untrained users.
MAINTENANCE.
Check moving parts for misalignment or binding,
there are no broken parts or other conditions that
may affect the operation of power tools. Power
tools are repaired before use when they are dama-
ged. Many accidents are caused by poorly maintai-
ned power tools. Use power tools, accessories and
tool tips, etc. according to these instructions and
in the manner provided for the particular type of
power tool, taking into account the conditions work
and work to develop. The use of this power tool
for applications other than those intended could
result in a dangerous situation. Please check your
power tool serviced by a Werku official repair servi-
ce using only identical replacement parts. This will
ensure the safety of this power tool is maintained.
CHECK CONDITION.
Make sure that all the screws in this power tool
are perfectly tightened. In cold climates or when
this power tool has not been used for a period,
allow this power tool to warm up by leaving it to
run empty for a few minutes, to ensure that all in-
ternal components are perfectly lubricated. Make
sure that the possible installed accessories are
perfectly fitted in place.
BEFORE OPERATION.
Make sure that this power tool is firmly suppor-
ted before using. Check that no one is standing
beneath you when using this power tool in high
areas. Keep your hands away from all moving
parts of this power tool.
DURING OPERATION.
Do not leave this power tool operating without ha-
ving it firmly fixed. Only turn it on when you are
sure you have full control over it. Do not point this
power tool at anyone while in use. When operating
this power tool will produce vibrations. The screws
may gradually come loose, and possibly cause
faults or accidents. Keep your hands away from
all moving parts of this power tool.
AFTER OPERATION.
Do not touch the possible accessories installed in
this power tool after use. It may be hot and cause
burns. Some materials worked with may contain
chemicals or toxic components. Avoid inhaling
these substances or allowing them to come into
contact with your skin. Use PPE designed to pre-
vent and protect against incidents of this kind.
3
English