MTD Yard Machines Y60 Manual Del Operador

Remove Unit From Carton Assemble The Unit
1 1 2
Remove all contents from Place shield onto mount
the carton. bracket. Securely screw 2 shield
screws through holes on mount
bracket and into shield. Make
sure screws are tightened equally
so there is an equal gap between
bracket and shield on each side.
Assemble The Unit
40:1
1 Gallon 3.2 oz
4 5
Mix thoroughly in separate Place unit on a level surface
fuel can: and fill fuel tank. DO NOT
– 3.2 fl. oz. of 2-cycle overfill.
engine oil
– 1 gallon of unleaded
gasoline
NOTE: Do not mix directly in
fuel tank.
Start The Unit
1 8 9
Crouch in starting position. SQUEEZE and HOLD
throttle for ALL further
steps.
Reload The Line*
Spool
Spring
Inner
Reel
3"-4"
Bump
Knob
1 1 2
Unscrew bump knob Insert 10' of 0.080"
®
counterclockwise. Remove SplitLine through hole in top
inner reel and spring. of reel. Pull most of line
through hole until 3"-4"
remains.
Reload The Line
Replacement SplitLine
Part #49U2134K953
For single line installation, refer to Line Installation
section of this manual.
For replacement spool installation, refer to
Installing a Prewound Reel section of this manual.
*This is to assist in the reloading of Splitline® only. These instructions
1 8
are NOT part of the fast assembly instructions. Line does not need to
be installed on the initial assembly and start-up.
Hold the inner reel in place.
Tighten Bump Knob
clockwise.
IMPORTANT: READ OPERATOR'S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
NEED HELP?
769-07118 P00
Y60
2-Cycle Trimmer
Operator's Manual
Min. 6"
3
Put handle on shaft. Move
handle a minimum 6 inches
away from shaft grip. Insert
bolt and tighten.
Start The Unit
Primer
Bulb
10 X
6 7
Press primer bulb 10 times, Move choke lever to
or until fuel is visible Position 1.
Choke Lever
5 X
10 11
Pull rope 5 times. Move choke lever to
Position 2 and squeeze
throttle.
3 4
Bend short end and push it Wind line tightly in direction
into the other hole. Pull tight. of arrow. Split other end of
®
SplitLine
®
:
Call 1-800-800-7310 in U.S. or 1–800–668–1238 in Canada
Tools Required:
• #2 Phillips screwdriver
D-Handle
Choke Lever
3-5 X
12
Pull rope 3-5 times to start
engine. Run unit for 30-60
seconds to warm up.
5
Push 6"-7" ends into 0.080"
holding slots.
back 6"-7".
Spark Plug
Choke Lever
Air Filter Cover
Starter Rope
Fuel Cap
On/ Off Switch
Throttle Control
DIDN'T START?
Cutting Head Shield
IF engine doesn't start, go back to step 6.
IF engine fails to start after 2 attempts, move
choke lever to position 3 and pull the starter
rope until engine starts.
Cutting Head
IF engine hesitates, return choke to Position
2 and continue to warm-up.
NOTE: unit is properly warmed up when
engine accelerates without hesitation.
Choke Lever
13 14
Continue to squeeze Continue to squeeze
throttle. Move choke lever throttle. Run unit for an
to Position 3. additional 60 seconds to
complete warm-up. Unit
may be used during this
time.
6 7
Insert or slide lines into the Pull lines firmly to release
eyelets in spool. Insert spring from holding slots.
and reel into spool.
Primer Bulb
04/11