Descargar Imprimir esta página
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

People's lives depend on your safe installation of our products. It is
important to read, understand and follow all instructions shipped
with the products. In addition, listed below are some other important
safety instructions and precautions you should follow:
To properly install this light, you must have a good understand­
ing of automotive electrical procedures and systems, along with
proficiency in the installation and use of safety warning equip­
ment.
DO NOT install equipment or route wiring or cord in the deploy­
ment path of an airbag.
If a vehicle seat is temporarily removed, verify with the vehicle
manufacturer if the seat needs to be recalibrated for proper air­
bag deployment.
When drilling into a vehicle structure, be sure that both sides of
the surface are clear of anything that could be damaged.
Locate light control so the VEHICLE and CONTROL can be oper­
ated safely under all driving conditions.
Do not attempt to activate or deactivate light control while driv­
ing in a hazardous situation.
This product contains high intensity LED devices. To prevent eye
damage, DO NOT stare into the light beam at close range.
You should frequently inspect the light to ensure that it is oper­
ating properly and that it is securely attached to the vehicle.
After testing is complete, provide a copy of these instructions to
the instructional staff and all operating personnel.
File these instructions in a safe place and refer to them when
maintaining and/or reinstalling the product.
Failure to follow all safety precautions and instructions may result in
property damage, serious injury, or death to you or others.
A.
OVERVIEW
The Federal Signal QuadraFlare LED Scene Light is a self-contained, high
intensity LED light designed for mounting to the exterior of a vehicle. Model
QL97LEDSCENE QuadraFlare LED scene lights are designed for operation on 12 Vdc.
INSTRUCTIONS
QUADRAFLARE™ 9 X 7 LED SCENE LIGHT
QL97LEDSCENE
SAFETY MESSAGE TO INSTALLERS
FOR
2562451C
REV. C 310
Printed in U.S.A.
loading

Resumen de contenidos para Federal Signal QUADRAFLARE QL97LEDSCENE

  • Página 5: Descripción

    DESCRIPCIÓN La Luz LED de la Escena QuadraFlare de Federal Signal es una luz LED autónoma de alta intensidad diseñada para montaje en el exterior de un vehículo. Las luces modelo de la escena de QL97LEDSCENE QuadraFlare LED se diseñan para la operación en 12 V CC.
  • Página 6: Instalacion

    DESEMPAQUE Después de desempacar la unidad, inspeccione si han ocurrido daños durante el envío. Si la unidad ha sufrido daños, no intente instalarla o ponerla en funcionamiento; entable una reclamación inmediatamente con el transportista, e indique la importancia de estos. Verifique cuidadosamente todos los sobres, etiquetas de envío y marbetes antes de removerlos o destruirlos.
  • Página 7 El conjunto de luces LED de la escena QuadraFlare incluye dos cables conductores de 12 pulg. de largo que salen por la parte posterior de la unidad, para realizar las conexiones eléctricas. Finalice las conexiones eléctricas según se describe en el párrafo E. Conexiones eléctricas.
  • Página 8 Servicio La instalación de Federal Signal proporcionará asistencia técnica cuando no se puedan resolver problemas a nivel local. Todas las unidades devueltas a Federal Signal para servicio, inspección o reparación deberán estar acompañadas de una Autorización de Devolución de Materiales.
  • Página 13 290A6249 LEGEND LEYENDA MOUNTING SCREW, #8 X 1-1/2, S.S. TORNILLO DE MONTAJE, #8 x 1-1/2 pulg., A.I. REFLECTOR REFLECTOR CONTROL PC BOARD ASSEMBLY CONJUNTO DE TABLERO DE CIRCUITO LED PC BOARD ASSEMBLY IMPRESO DE CONTROL BASE CONJUNTO DE TABLERO DE CIRCUITO GASKET IMPRESO DE LED VEHICLE BODY...
  • Página 14 7.25 (2X) 3.63 (2X) Ø 1.00 Ø .25 (4) PLCS 2.63 (2X) 5.25 (2X) 290A5840 Figure 2. / Figura 2. / Figure 2. -14-...
  • Página 15 290A6248 LEGEND LEYENDA VENT HOLE ORIFICIO DE VENTILACION 3/4” COLOR CODED STICKER DOTS LOS AUTOADHESIVOS EN FORMA DE PUNTOS TO BE APPLIED TO IDENTIFY THE CODIFICADOS POR COLORES DE 3/4 PULG. CORRESPONDING PC BOARD SE APLICARAN PARA IDENTIFICAR EL COLOR ASSEMBLY LED COLOR ON EACH DEL LED CORRESPONDIENTE EN EL TABLERO SIDE.
  • Página 16 www.fedsig.com...