Broan EVOLUTION 1 QP142 Serie Manual Del Usario
Ocultar thumbs Ver también para EVOLUTION 1 QP142 Serie:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

EVOLUTION
QP142 Series Range Hoods
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-
JURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufac-
turer. If you have questions, contact the manufacturer at the
address or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the ser-
vice disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring (including switch loca-
tion) must be done by a qualified person(s) in accordance
with all applicable codes and standards, including fire-rated
construction.
4. Provide sufficient air for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the combustion equipment
standards such as those published by the National Fire Pro-
tection Association (NFPA), the American Society for Heat-
ing, Refrigeration and Air Conditioning Engineers (ASHRAE),
and local codes.
5. This product may have sharp edges. Be careful to avoid cuts
and abrasions during installation and cleaning.
6. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
7. Ducted fans must always be vented to the outdoors.
8. Use only metal ductwork.
9. Do not use this fan with any solid-state speed control device.
10. As an alternative, this product may be installed with the UL-
approved cord kit designated for the product, following in-
structions packed with the cord kit.
11. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may ig-
nite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
cooking flaming foods (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).
3. Clean ventilating fans frequently. Grease should not be al-
lowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for
the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet,
or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
1
TM
FOR DOMESTIC COOKING ONLY
MODELS QP142SS • QP142WW • QP142BL
WARNING
2. NEVER PICK UP A FLAMING PAN — You may be burned or
spread the fire.
3. DO NOT USE WATER, including wet dishcloths or towels -
violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA.
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust haz-
ardous or explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or unbal-
anced impeller, keep drywall spray, construction dust, etc.,
off power unit.
4. Do not use over cooking equipment greater than 60,000
BTU/hr. as the blower motor will shut down intermittantly.
5. Your hood motor has a thermal overload which will automati-
cally shut off the motor if it becomes overheated. The motor
will restart when it cools down. If the motor continues to shut
off and restart, have the hood serviced.
6. The top of the hood MUST NOT BE LESS than 24" and at a
maximum of 30" above cooktop for best capture of cooking
impurities.
7. This hood is not intended to be used as a shelf.
8. Please read specification label on product for further infor-
mation and requirements.
NOTE If hood is to be installed non-ducted:
Purchase a set of (3) non-ducted filters (Model
BPPF42) from your local distributor or retailer and
attach them to the aluminum mesh filters.
Register your product online at: www.broan.com
Installer: Leave this manual
with the homeowner.
Homeowner: Cleaning, Maintenance and
Operating instructions on page 2.
Page 1
Tabla de contenido
loading

Resumen de contenidos para Broan EVOLUTION 1 QP142 Serie

  • Página 15 3. Limpie frecuentemente los ventiladores. No permita la acumulación de grasa en el ventilador ni en el filtro. Registre su producto en Internet en: www.broan.com 4. Use una cacerola del tamaño adecuado. Siempre use utensilios de cocina que sean apropiados para el tamaño del elemento de Aviso al instalador: Deje este manual la superficie.
  • Página 16: Limpieza Y Mantenimiento

    MODELOS QP142SS • QP142WW • QP142BL Página 16 CONTENIDO FUNCIONAMIENTO SE INCLUYE CON LA CAMPANA: ENCIENDA siempre la campana antes de comenzar a cocinar, a fin de establecer un flujo de aire en la cocina. Después de apagar la estufa, deje que la campana funcione durante unos cuantos minutos para despejar el aire. CONECTOR PARA REGULADOR/ Para hacer funcionar la campana, haga lo siguiente: CONDUCTO DE 3¼ X 10 PULG. (8.3 X 25.4 CM) FILTROS PARA GRASA CONECTOR PARA INTERRUPTOR DEL VENTILADOR CONDUCTO REDONDO Este interruptor oscilante de 3 posiciones ENCIENDE y APAGA el DE 7 PULG.
  • Página 17: Prepare La Campana

    MODELOS QP142SS • QP142WW • QP142BL Página 17 PREPARE LA CAMPANA Guíese por el diagrama correspondiente (a continuación) para colocar los conductos y hacer el corte exacto para la conexión eléctrica en el gabinete o en la pared. Para instalaciones en sistemas sin conductos, NO haga ningún orificio de acceso Quite la bolsa de piezas del interior de la tapa del extremo del para conducto. empaque de espuma. CONDUCTO VERTICAL DE TORNILLOS DE MONTAJE Quite todo el forro de plástico protector de la campana 3¼ X 10 PULG. (8.3 X 25.4 CM) DE LA CAMPANA (5) (únicamente campanas de acero inoxidable). 17 5/8 pulg. 17 5/8 pulg.
  • Página 18 MODELOS QP142SS • QP142WW • QP142BL Página 18 TORNILLOS DESVIADOR PARA SISTEMAS SIN CONDUCTOS CAJA DE AIRE ÚNICAMENTE EN INSTALACIONES SIN CONDUCTOS: PLACA DE De la lista de piezas: Fije el desviador para sistemas sin SISTEMA SIN conductos a la caja de aire con 2 tornillos y 2 arandelas. CONDUCTO ÚNICAMENTE EN INSTALACIONES SIN CONDUCTOS: TORNILLOS Inserte el extremo corto de la placa sin conducto en la ranura del pleno sin conducto. Fije con los 2 tornillos que quitó en el paso 9. 11 ÚNICAMENTE EN INSTALACIONES SIN CONDUCTOS: Compre un juego de (3) filtros para sistemas sin conductos (Modelo BPPF42) en la tienda distribuidora o minorista de su localidad. Siguiendo las instrucciones que acompañan...
  • Página 19: Instale La Campana

    MODELOS QP142SS • QP142WW • QP142BL Página 19 INSTALE LA CAMPANA PLACA REDONDA DE AGUJERO CIEGO ADVERTENCIA DE 7 pulg. (17.8 cm) (también desmonte la Para reducir el riesgo de una descarga eléctrica, desconecte placa vertical de 3¼ x el suministro eléctrico al panel de servicio. Bloquee el panel 10 pulg. [8.3 x 25.4 cm]) de servicio o póngale una etiqueta de seguridad para evitar que alguien conecte accidentalmente la energía eléctrica. PLACA HORIZONTAL DE 3¼ X 10 PULG. PLACA VERTICAL (8.3 X 25.4 CM) DE AGUJERO CIEGO CUBIERTA DE DE 3¼ X 10 PULG. LA CAJA DE (8.3 X 25.4 CM) CABLEADO ELÉCTRICO 12 ÚNICAMENTE EN INSTALACIONES CON CONDUCTOS: Retire las placas de agujero ciego vertical de 3¼ x 10 pulg.
  • Página 20: Conecte El Cableado

    Esta garantía sustituye todas las garantías anteriores. sirve para instalar y quitar bombillas de luz. Para tener derecho al servicio de la garantía, usted debe (a) notificar a Broan NuTone a Alinee las clavijas de la bombilla con la abertura de diámetro la dirección y número de teléfono que aparecen abajo, (b) proporcionar el número de modelo y la identificación de la pieza y (c) describir la naturaleza de cualquier defecto...
  • Página 21: Piezas De Servicio

    MODELOS QP142SS • QP142WW • QP142BL Página 21 PIEZAS DE SERVICIO Ahora se puede hacer los pedidos de las piezas de repuesto en nuestro sitio Web. Visítenos en www.broan.com CLAVE N.º PIEZA N.º DESCRIPCIÓN 97017727 Placa redonda de 7 pulg. (17.8 cm) (incluye piezas de montaje) 97017729 Montaje de interruptor blanco (incluye 2 interruptores, placa de identificación, piezas de montaje) 97017730 Montaje de interruptor negro (incluye 2 interruptores, placa de identificación, piezas de montaje) 99526653 Placa de identificación, blanca...

Este manual también es adecuado para:

Evolution 1 qp142ssEvolution 1 qp142wwEvolution 1 qp142bl

Tabla de contenido