Descargar Imprimir esta página

INNO TR145 Instrucciones De Instalación

Ganchos de anclaje
Ocultar thumbs Ver también para TR145:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation Instructions
Before using the Mounting hooks, carefully read the installation instructions as well as the installation
instructions for basic carrier systems, and follow all usage instructions. After reading the installation
instructions, keep it in a safe place along with the installation instructions for basic carrier systems. If you
are to give the mounting hooks to a third person, provide the installation instructions to ensure safe
installation and usage. If you have any questions regarding the installation instructions, contact our
customer service listed below.
WARNING
Install hooks correctly at specified positions according to the installation instructions herein and the installation instructions for the
applicable carrier system. Installation positions of hooks depend on the vehicle type. If hooks are not installed at specified
positions, the carrier may fall and cause accidents. If the installation instructions appropriate for your vehicle type are not
available, contact our customer service listed below.
Select hooks matching your vehicle by referring to the Fit Guide available at stores or on our website : www.innoracks.com.
If inappropriate hooks are used, the carrier / attachment may fall and cause accidents.
Before driving the vehicle, rock the stays and bars in all directions to ensure that there is no looseness. Retighten any loose
knobs or bolts.
Do not use these hooks for attachments of non-specified types.
The carrier may fall and cause accidents.
Observe the specified loading conditions.
Failure to observe the loading condition may cause the carrier to break or loosen and fall, resulting in accidents.
For INNO dedicated ski & snowboard carriers, read the carrier installation instructions to determine proper
mounting locations.
The TR Mounting hooks include the parts listed below. Verify that all of these parts are
included in the carrier system you have purchased. In the event any of these parts are
missing, contact our customer service listed below.
1
2
5
6
7
NOTE
The specifications or external appearance of this product or any of the genuine
spare parts may be changed for improvement without prior notification.
Contact Information
If you have any comments, questions or suggestions, contact our customer service listed below.
Car Mate USA shall not be held liable for any accidents or incidental losses arising from improper installations or usage.
Furthermore, Car Mate USA shall not be held liable for any accidents or incidental losses arising from installation or usage after
the customer has made any modifications to the system's original configuration or specifications.
If you can not find your vehicle on the following page(s), contact us for more information.
Car Mate USA, Inc.
383 Van Ness Ave., Suite 1603,
Torrance, CA 90501 U.S.A.
support@innoracks.com
www.innoracks.com
14539451A-
TR145
TR Fit Hooks
Part
Cushion base 512
3
4
Base bracket
Spacer [20mm]
20mm
32mm
Bolt [M6x32mm]
Protection sheet
8
Hex Wrench [B=4]
Base Cover
Installation Instructions
4182808TR1451
EN
Qty
4
4
4
4
8
1
4
1
08 / 2014
-EN
-A
loading

Resumen de contenidos para INNO TR145

  • Página 9: Información De Contacto

    No respetar las condiciones de carga puede provocar que el portacargas se rompa o se afloje y caiga, lo que causaría un accidente. Para los portacargas exclusivos para esquís y tablas de snowboard de INNO lea los manuales de instrucciones del portacargas para determinar las ubicaciones de montaje correctas.
  • Página 10 TR145 Instalación de las bases de Procedimiento de instalación para modelos de vehículos individuales amortiguación Separador Condiciones de carga Inserte el espaciador en el orificio de Fabricante Modelo Tipo Año Capacidad Coussinet de base Bicicleta máxima de carga instalación de la base del amortiguador.
  • Página 11 TR145 Instalación de las bases de Procedimiento de instalación para modelos de vehículos individuales amortiguación Separador Condiciones de carga Fabricante Modelo Tipo Año Inserte el separador en el orificio de Capacidad Coussinet de base Bicicleta máxima de carga instalación de la base del libras amortiguador.
  • Página 12 TR145 Instalación del sistema de portacargas Coloque la unidad de la base en la base 4N・m del amortiguador / abrazadera de la Clé hexagonale Boulon base que se han instalado. Luego, [M6×15] con la llave hexagonal (incluida), sujétela ajustando de forma alternada...