Idiomas disponibles

Idiomas disponibles

INSTALLATION INSTRUCTIONS
FREESTANDING TUB
2764 SERIES
HIGH GLOSS ACRYLIC SURFACE
Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation
proceeds smoothly--please read these instructions carefully before you begin.
BEFORE YOU BEGIN....
Local building codes vary by location. Observe all local plumbing and building codes.
Your new bath is shipped to you after careful inspection.
To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.
!
NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.
BEFORE INSTALLING : please see your product spec page to verify the dimensions and water supply connections.
!
Visit our website where you can search by Model number for the product spec page at:
http://www.americanstandard-us.com/
TOOLS & MATERIALS REQUIRED
TOOLS:
• Level
• Square
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard Woodworking Tools
1
INSTALLATION INSTRUCTIONS:
A. Set up the cover in the desired location. Locate
the drain outlet location and supply line locations
for the faucet (see faucet instructions).
B. Recommend cutting floor cutout - 10" x 5-5/8"
(254mm x 143mm) use cover as guide, as shown
in rough-in detail.
C. Mark lines on the floor for the cover location. Use
these to relocate cover.
D. Turn the cover over and apply silicone caulking to
the bottom of the cover as shown.
(Note: See instructions for the Over ow Drain Kit included.)
2
A. Set cover down in place and secure to the floor with
6 screws (not provided) through wood strip locations.
B. Apply foam tape to outside top edge, even with the
top edge. Trim away excess gasket.
FOAM
All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.
© AS America, Inc. 2019
• Personal Safety Equipment
• Caulking Gun
• Adjustable Wrench
• 3/32" Allen Wrench
• Hacksaw
• Sandpaper
SCREW HERE
MATERIALS:
• Screws
• Silicone Caulking
3
A. Assemble drain to tub per instructions below.
754782-100 Rev. 8 7/19
Tabla de contenido
loading

Resumen de contenidos para American Standard 2764 Serie

  • Página 5: Antes De Instalar

    BAÑERA NO EMPOTRADA SUPERFICIE DE ACRÍLICO CON BRILLO ESPECIAL 2764 SERIE Gracias por elegir American Standard, referente de calidad durante más de 100 años. Para asegurarse de realizar la instalación sin inconvenientes, lea atentamente estas instrucciones antes de comenzar. ANTES DE COMENZAR...
  • Página 6 DE DESAGÜE DEL - 1 INSTRUCCIONES DE INSTALACIÓN: Deslice las tuercas del desagüe y las arandelas de polivinílico sobre el EL REBOSADERO Y EL TUBO DEL CODO DE DESAGÜE DEBEN rebosadero y los tubos de desagüe. KIT DE EXTENDERSE 1" A 1-1/2" EN LOS REBOSADERO Ensamble el rebosadero y los tubos de desagüe sin mucha tensión al tubo EXTREMOS DEL TUBO...
  • Página 7 DE DESAGÜE DEL - 6 KIT DE PISTÓN Ajuste el perno y la contratuerca de pistón de latón para una abertura PERNO Y CONTRATUERCA mínima de 1/2"-5/8", luego ajuste la contratuerca contra el eje del DE PISTÓN DE LATÓN pistón para fijar el ajuste de la altura. PRECAUCIÓN: La contratuerca de pistón debe ajustarse contra el 1/2"-5/8"...
  • Página 8: Mantenimiento Y Limpieza

    3. Aplicación comercial. 4. Opciones y accesorios. La garantía limitada de American Standard sobre estos productos es de un año sólo para las piezas y no cubre gastos de mano de obra. Esta garantía limitada por un año cubre accesorios fabricados por American Standard (por ejemplo, revestimientos, drenajes, barras de agarre, calentadores, juegos de molduras) contra defectos de material o mano de obra.

Tabla de contenido