Ocultar thumbs Ver también para MultiChoice T75P6 Serie:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

T75P5_______
T75P6_______
Register Online
www.brizo.com/customer-support/product-registration
To reference replacement parts and access additional
technical documents and product info, visit www.brizo.com
?
1-877-345-BRIZO (2749)
brizosupport@brizo.com
Read all instructions prior to installation.
Failure to read these instructions prior to installation may result in personal
injury, property damage, or product failure. Manufacturer assumes no
responsibility for product failure due to improper installation.
You may need:
CAUTION: This system/device must be set by the
installer to ensure safe, maximum temperature.
Any change in the setting may raise the discharge
temperature above the limit considered safe and
may lead to hot water burns.
NOTICE TO INSTALLER: CAUTION!–As the
installer of this valve, it is your responsibility
to properly INSTALL and ADJUST this valve
per the instructions given. This valve does
not automatically adjust for inlet temperature
changes, therefore, someone must make the
necessary rotational limit stop adjustments at
the time of installation and further adjustments
may be necessary due to seasonal water
temperature change. YOU MUST inform the
owner/user of this requirement by following the
instructions. If you or the owner/user are unsure
how to properly make these adjustments, please
refer to page 5 and if still uncertain, call us at
1-877-345-BRIZO (2749).
After installation and adjustment, you must affix
your name, company name and the date you
adjusted the temperature knob to the caution label
provided and apply or attach the label to the back
side of the closest cabinet door and the warning
label to the water heater. Leave this Instruction
Sheet for the owner's/user's reference.
106855 Rev. B
1/14/20
!
CAUTION
!
3/32"
Pressure-Balance
MultiChoice
with Integrated 3 or 6
Diverter Trim
WARNING: This pressure-balanced valve is
designed to minimize the effects of outlet water
temperature changes due to inlet pressure
and temperature changes, commonly caused
by dishwashers, washing machines, toilets
and the like. There is a risk of hot water
burns and other personal injury when there
is a failure of other temperature controlling
devices elsewhere in the plumbing system if
the rotational limit stop is not properly set or if
the hot water temperature is changed after the
settings are made or if the water inlet changes
due to seasonal changes. To minimize this risk,
caution should be used when using the hot
water knob.
WARNING: Do not install a shut-off device on
either outlet of this valve. When this type of
device shuts off the water flow, it can defeat
the ability of the valve to balance the hot and
cold water pressures.
CAUTION: Failure to read these instructions
prior to installation may result in personal injury
or property damage. Manufacturer assumes no
responsibility for product failure due to improper
installation.
1
Valve
®
Rev. B
Tabla de contenido
loading

Resumen de contenidos para Brizo MultiChoice T75P6 Serie

  • Página 8 Diverter Handle Reference Sheet Water Flow For 3 Function Diverter / Flujo de agua para Desviadores de 3 posiciones / Écoulement de l’eau pour les inverseurs à 3 positions 1st Position 2nd Position * 3rd Position 1 ª posición Outlet 1 2 ª...
  • Página 9 5 y si aún tiene duda, caliente. llámenos al 1-877-345-BRIZO (2749). ADVERTENCIA: No instale un dispositivo de cierre en cualquiera de las tuberías de Después de la instalación y el ajuste, debe colocar salida de agua de esta válvula.
  • Página 10: Limpieza Y Cuidado

    El comprobante de compra (recibo de venta original) del comprador original debe estar disponible a Brizo Kitchen & Bath Company para todos los reclamos de garantía a menos que el comprador haya registrado el producto con Brizo Kitchen & Bath Company. Esta garantía se aplica solo a las llaves de agua Brizo®...
  • Página 11: Instalación Del Cartucho

    Instalación del cartucho Gire el cartucho de la válvula (1) de forma que las Cierre los suministros de agua. Quite la tapa (1), las palabras "HOTTER COLDER" estén en la parte superior. tuercas tapas (2) y las tapas de prueba (3) del cuerpo de Inserte el cartucho en el cuerpo de la tubería preliminar.
  • Página 12: Instalación Del Cartucho Desviador

    Instalación del cartucho desviador Para la instalación del casquete PARA LA INSTALACIÓN DEL CARTUCHO DE DESVÍO: Deslice la tuerca tapa (1) sobre el casquillo desviador (2) Aplique una capa ligera de grasa para plomería en y enrosque en el cuerpo de la tubería preliminar. el cartucho del desviador y en el casquillo (4) y en la ATENCIÓN: Apretar demasiado puede provocar daños junta tórica (2) para facilitar la instalación del casquillo...
  • Página 13: Ajuste Del Tope Del Limite De La Temperatura

    Ajuste del tope del limite de la temperatura Hotter Cooler ADVERTENCIA: El tope del límite de rotación se utiliza para limitar la debe reposicionar hacia la derecha para disminuir la cantidad de agua caliente disponible de manera que, si temperatura del agua de la válvula de salida a menos de se configura correctamente, una lesión por quemadura es 120°...
  • Página 14: Instalación De La Manija

    Instalación del casquillo del accesorio Instalación del chapetón Inserte el espaciador (3) en la manga (1) y empújelo Para paredes acabadas de un grosor hasta 1 1/8". Fije la hacia adelante. Deslice el manguito de ajuste (1) sobre el placa posterior (1) al cuerpo de la unidad de las tuberías bonete (2), el cartucho de la válvula y el cuerpo enrasado.
  • Página 15: Mantenimiento

    Instalación de la manija Instalación de la manija del desviador Models with sunken handle Deslice la manija del desviador (1) sobre el manguito Install stem extender (1) onto valve stem and de ajuste (2). Usando una llave hexagonal, inserte el secure with screw (2).
  • Página 16: Hoja De Referencia Para La Manija Desviadora

    Hoja de referencia para la manija desviadora Water Flow For 3 Function Diverter / Flujo de agua para Desviadores de 3 posiciones / Écoulement de l’eau pour les inverseurs à 3 positions 1st Position 3rd Position 2nd Position * 1 ª posición Outlet 1 2 ª...
  • Página 23 Installation de la manette Installation de la manette d’inverseur Glissez la manette d’inverseur (1) sur le manchon de finition (2). Models with sunken handle À l’aide d’une clé hexagonale, introduisez la vis de Install stem extender (1) onto valve stem and calage (3) dans la manette (1).
  • Página 24 Hoja de referencia para la manija desviadora Water Flow For 3 Function Diverter / Flujo de agua para Desviadores de 3 posiciones / Écoulement de l’eau pour les inverseurs à 3 positions 1st Position 2nd Position * 3rd Position 1 ª posición Outlet 1 2 ª...

Tabla de contenido