Descargar Imprimir esta página

Publicidad

Enlaces rápidos

IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property damage, serious injury, and/
or death to those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understood the safety information
contained in this manual.
1.
Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2.
Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3.
This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including fire.
4.
Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without
losing eye contact with the roadway.
5.
Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag
deployment area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death.
Refer to the vehicle owner's manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable
mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6.
It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
7.
The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is the vehicle operator's responsibility to be sure they can proceed safely before entering an
intersection, drive against traffic, respond at a high rate of speed, or walk on or around traffic lanes.
8.
This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The
manufacturer assumes no liability for any loss resulting from the use of this warning device.
Specifications:
Size:
5590XXX
5590XXX-VM
5590XXX-MG
5597XXX
5597XXX-VM
5597XXX-MG
Weight: Permanent mount
Vacuum-Magnet Mount
Magnet Mount
Input Voltage:
12 to 48 VDC systems
Installation & Mounting:
IMPORTANT! This unit is a safety device and it must be connected
to its own separate, fused power point to assure its continued
operation should any other electrical accessory fail.
Carefully remove the Minibar and place it on a flat surface. Examine the
unit for transit damage, and locate all parts. If damage is found, or parts
are missing, contact the transit company or ECCO. Do not use damaged or
broken parts.
CAUTION!
When drilling into any vehicle surface, make sure that the
area is free from any electrical wires, fuel lines, vehicle
upholstery, etc. that could be damaged.
Installation and Operation Instructions
5590 Series LED Minibars
15" x 9" x 2.5"
15" x 9" x 3.1"
15" x 9" x 2.7"
15" x 9" x 2.5"
15" x 9" x 3.1"
15" x 9" x 2.7"
approx. 4.0 lbs.
approx. 6.3 lbs.
approx. 6.25 lbs.
Current Draw:
Maximum power consumption:
5590/5597: 6.0 Amps Maximum
Maximum power consumption: 84 watts
Flash Rate:
See Flash Pattern Chart
Temp. Range:
-30ºC to +50ºC
Page 1 of 7

Publicidad

loading

Resumen de contenidos para Ecco 5590 Serie

  • Página 1 Carefully remove the Minibar and place it on a flat surface. Examine the unit for transit damage, and locate all parts. If damage is found, or parts are missing, contact the transit company or ECCO. Do not use damaged or broken parts.
  • Página 2 The VM and MG mount models have flash pattern select via a momentary switch on the cigarette plug. FUSE (10A) Flash Pattern Synching (USER SUPPLIED) YELLOW The 5590 and 5597 permanent mount models sync with other compatible ECCO SYNC SWITCH WHITE products via the yellow wire: (USER SUPPLIED)
  • Página 3 WARNING! Maximum recommended vehicle speed for safe operation using the Vacuum Mount model is 65 mph (104 km/h) when fitted to the center of a vehicle roof of steel construction. Higher speeds could cause the mount to fail, resulting in the minibar flying off of the vehicle, which could cause damage to other vehicles and injury or death to the passengers.
  • Página 4 SINGLE COLOR FLASH PATTERN CHART Pattern Mode Description Sync SAE J845 CA T13 (DEFAULT) Single Flash Phase 1  Single Flash Phase 2 Single Flash Alternating Split Single Flash Phase 1  Single Flash Phase 2 Single Flash Alternating Split Double Flash Phase 1 Double Flash Phase 2 Double Flash Alternating Split Double Flash Phase 1 Double Flash Phase 2 Double Flash Alternating Split Quad Flash Phase 1 Quad Flash Phase 2 Quad Flash Alternating Split Quad Flash Phase 1 Quad Flash Phase 2 Quad Flash Alternating Split Triple Flash Phase 1 Triple Flash Phase 2 Triple Flash Alternating Split Quint Flash Phase 1 Quint Flash Phase 2 Quint Diagonal Rotate Double Diagonal Phase 1 Double Diagonal Phase 2 Double Diagonal Rotate Quad Diagonal Phase 1 Quad Diagonal Phase 2 Quad Diagonal Rotate Fast Rotate Rotate/Quad 150/75 Wave Rotate Random...
  • Página 5 DUAL COLOR FLASH PATTERN CHART Pattern Mode 1 Mode 2 Mode 1+2 Description Sync Phase SAE J845 CA T13 SAE/T13 Single Color 1 Phase 1 (DEFAULT) SAE/T13 Single Color 1 Phase2 SAE/T13 Single Split Color Phase 1 SAE/T13 Single Split Color Phase 2 SAE/T13 Single Color 2 Phase 1 (DEFAULT) SAE/T13 Single Color 2 Phase 2 SAE/T13 Single Dual Color Phase 1 (DEFAULT) SAE/T13 Single Dual Color Phase 2 SAE/T13 Single Alternating Split Color 1 & Color 2 Single Color 1 Phase 1 Single Color 1 Phase 2 Single Split Color Phase 1 Single Split Color Phase 2 Single Color 2 Phase 1 Single Color 2 Phase 2 Single Dual Color Phase 1 Single Dual Color Phase 2 Single Alternating Split Color 1 & Color 2 SAE/T13 Double Color 1 Phase 1 SAE/T13 Double Color 1 Phase 2 SAE/T13 Double Split Color Phase 1 SAE/T13 Double Split Color Phase 2  SAE/T13 Double Color 2 Phase 1 SAE/T13 Double Color 2 Phase 2 SAE/T13 Double Dual Color Phase 1 SAE/T13 Double Dual Color Phase 2 SAE/T13 Double Alternating Split Color 1 & Color 2 ECER65/SAE Double Color 1 Phase 1 ECER65‐SAE Double Color 1 Phase 2 ECER65/SAE Double Split Color Phase 1 ECER65/SAE Double Split Color Phase 2 ECER65/SAE Double Color 2 Phase 1 ECER65/SAE Double Color 2 Phase 2...
  • Página 6 DUAL COLOR FLASH PATTERN CHART Pattern Mode 1 Mode 2 Mode 1+2 Description Sync Phase SAE J845 CA T13 ECER65/SAE Quad Color 1 Phase 1 ECER65/SAE Quad Color 1 Phase 2 ECER65/SAE Quad Split Color Phase 1 ECER65/SAE Quad Split Color Phase 2 ECER65/SAE Quad Color 2 Phase 1 ECER65/SAE Quad Color 2 Phase 2 ECER65/SAE Quad Dual Color Phase 1 ECER65/SAE Quad Dual Color Phase 2 ECER65/SAE Quad Alternating Split Color 1 & Color 2 Double Diagonal Alternate Color 1 Phase 1 Double Diagonal Alternate Color 1 Phase 2 Double Diagonal Alternate Split Color Phase 1 Double Diagonal Alternate Split Color Phase 2 Double Diagonal Alternate Color 2 Phase 1 Double Diagonal Alternate Color 2 Phase 2 Double Diagonal Alternate Dual Color Phase 1 Double Diagonal Alternate Dual Color Phase 2 Quad Diagonal Alternate Color 1 Phase 1 Quad Diagonal Alternate Color 1 Phase 2 Quad Diagonal Alternate Split Color Phase 1 Quad Diagonal Alternate Split Color Phase 2 Quad Diagonal Alternate Color 2 Phase 1 Quad Diagonal Alternate Color 2 Phase 2 Quad Diagonal Alternate Dual Color Phase 1 Quad Diagonal Alternate Dual Color Phase 2 Fast Rotate Color 1 Fast Rotate Color 2 Fast Rotate Dual (Color 1 then Color 2) Rotate/Quad Color 1  150/75 Rotate/Quad Color 2 Rotate/Quad Dual (Color 1 then Color 2) Wave Rotate Color 1...
  • Página 7 833 West Diamond St, Boise, Idaho 83705 Customer Service USA 800-635-5900 UK +44 (0)113 237 5340 | AUS +61 (0)3 63322444 ECCOESG.com An ECCO SAFETY GROUP™ Brand ECCOSAFETYGROUP.com © 2012 ECCO, Inc. All rights reserved. 920-4300-00 Rev. H Page 7 of 7...
  • Página 8 Examine la unidad para detectar si se produjeron daños durante el traslado y ubique todas las piezas. Si se encuentran daños o si faltan piezas, comuníquese con la empresa de transporte o con ECCO. No utilice piezas dañadas o rotas.
  • Página 9 Los modelos de montaje permanente 5590 y 5597 se sincronizan con otros SELECIÓN DEL PATRÓN SELECCIÓN DE PATRÓN (AISLAR CUANDO DESTELLOS DE INTERMITENCIA productos ECCO compatibles a través del cable AMARILLO: NO SE UTILICE) (MOMENTÁNEO A TIERRA) (AISLAR CUANDO NO SE UTILICE) ATENUACIÓN (+) 1.
  • Página 10 ¡ADVERTENCIA! La velocidad máxima sugerida para el vehículo para un uso seguro del modelo con montaje en vacío es de 65 mph (104 km/h) cuando está colocada en el centro del techo de un vehículo de construcción de acero. Las velocidades más elevadas podrían hacer fallar el montaje desprendiendo la microbarra del vehículo, lo cual podría ocasionar daños a otros vehículos y lesiones o el deceso de los pasajeros.
  • Página 11 833 West Diamond St, Boise, Idaho 83705 Servicio Al Cliente EE.UU. 800-635-5900 Reino Unido +44 (0)113 237 5340 | AUS +61 (0)3 63322444 ECCOESG.com An ECCO SAFETY GROUP™ Brand ECCOSAFETYGROUP.com © 2012 ECCO, Inc. Todos los derechos reservados. 920-4300-00 Rev. G Página 4 de 4...
  • Página 12 Assurez-vous que l’unité n’a pas été abîmée dans le transport et repérez toutes les pièces. Si vous repérez un dommage ou des pièces manquantes, contactez la société de transport ou ECCO. N’utilisez pas de pièces cassées ou abîmées. Page 1 sur 4...
  • Página 13 Montage permanent : REMARQUE : si vous faites fonctionner le véhicule sans la 1. Sélectionnez une surface de montage plane pour mini-barre à installer. La lentille externe installée sur le produit, vous causerez des visibilité du clignotement et la simplicité d’accès du câblage doivent être dommages NON couverts par la garantie.
  • Página 14 AVERTISSEMENT! La vitesse maximale recommandée du véhicule pour une utilisation en toute sécurité du modèle à montage à vide est de 104 km/h (65 mph) lorsqu’il est mis en place au centre du toit en acier d’un véhicule. Si vous roulez à des vitesses élevées, la mini- barre pourrait se détacher du véhicule et endommager d’autres véhicules, et blesser voire tuer les passagers.
  • Página 15 833 West Diamond St, Boise, Idaho 83705 Le Service Client États-Unis 800-635-5900 Royaume-Uni +44 (0)113 237 5340 | AUS +61 (0)3 63322444 ECCOESG.com An ECCO SAFETY GROUP™ Brand ECCOSAFETYGROUP.com © 2012 ECCO, Inc. Tous droits réservés. 920-4300-00 Rev. H Page 4 sur 4...

Este manual también es adecuado para:

5597 serie