nVent RAYCHEM SC-JBS-S-A Instrucciones De Instalación

SC-JBS-S-A
Splice Connection with Junction Box Installation Instructions
APPROVALS
Hazardous Locations
Class I, Div. 2, Groups A, B, C, D
Class II, Div. 2, Groups F, G
Class III
– WS
09-IEx-0008X
Ex e IIC T* Gb (2)
Ex e II T* (see schedule)
IECEx
Ex tD A21 IP66
IECEx BAS 06.0049X
KIT CONTENTS
Item Qty Description
A 1 Stand assembly
B 1 Cable lubricant
C 12 Tape strips
D 2 Green/yellow tubes
E 4 Coils Kester 48 core LF solder for nickel
®
F 12 Thomas & Betts splices, spares included
G 1 Junction box
H 1 Lid
I 1 Spanner
J 1 Strain relief
WARNING:
This component is an electrical device that must be installed
correctly to ensure proper operation and to prevent shock or
fire. Read these important warnings and carefully follow all of
the installation instructions.
• To minimize the danger of fire from sustained electrical
arcing if the heating cable is damaged or improperly
installed, and to comply with the requirements of nVent,
agency certifications, and national electrical codes,
ground-fault equipment protection must be used. Arcing
may not be stopped by conventional circuit breakers.
• Be sure all power sources are de-energized before
opening box.
• Keep components and heating cable ends dry before and
during installation.
(1)
Ex e II T
– WS
(1) for T-Rating, see design
documentation
• Component approvals and performance are based on the
use of nVent-specified parts only. Do not use substitute
parts or vinyl electrical tape.
• Soldering tools or torches can cause fire or explosion
in hazardous areas. Be sure there are no flammable
materials or vapors in the area before using these tools.
• Damaged conductors can overheat or short. Do not
break conductor wire strands when scoring the jacket or
removing insulation.
• Use only fire-resistant insulation materials, such as
fiberglass wrap or flame-retardant foam.
• Wrap exposed conductors with supplied tape strips to
prevent shorts.
DESCRIPTION
The nVent RAYCHEM SC-JBS-S-A is a NEMA 4X-rated splice
connection kit designed for use with nVent RAYCHEM 2 and 3SC30,
40, 50 (-CT), 2 and 3SC/H30, 40, 50 (-CT) and 2 and 3SC/F30, 40, 50
(-CR) series heating cables in hazardous locations.
This kit may be installed at temperatures as low as –40°F (–40°C).
For easier installation, store above freezing until just before installation.
For technical support, call nVent at (800) 545-6258.
TOOLS REQUIRED
• Diagonal cutters
• Wire strippers
• Solder tool or torch (with small tip)
• Thomas & Betts TBM5S crimp tool (P/N P000000585) or
WT2000 crimp tool (P/N 273435-000) tool or equivalent.
Crimp tools can be ordered from nVent.
ADDITIONAL MATERIALS REQUIRED
• Pipe straps (2)
• Glass cloth tape:
– GT-66 for installation temperature above 40°F (4°C)
– GS-54 for installation temperature above –40°F (–40°C)
OPTIONAL MATERIALS
• Recommended conduit drain:
JB-DRAIN-PLUG-3/4IN (P/N 278621-000)
• Pipe adapter to increase stand height:
SC-JB-PIPE-ADAPTER (P/N P000000648)
A
B
C
D
E
F
HEALTH HAZARD: Hot solder can burn eyes and skin.
Fumes during soldering are irritating to eyes and may cause
headache and respiratory system irritation or damage.
Prolonged or repeated exposure to rosin flux fumes during
soldering may result in allergic reaction in a sensitive person,
resulting in asthma symptoms. Consult MSDS VEN 0043 for
further information.
CHEMTREC 24-hour emergency telephone: (800) 424-9300
Non-emergency health and safety information:
(800) 545-6258
• Slotted screwdriver
• Utility knife
J
I
H
G
CAUTION: