Descargar Imprimir esta página
DeWalt DW131 Manual De Instrucciones
DeWalt DW131 Manual De Instrucciones

DeWalt DW131 Manual De Instrucciones

Taladros 13 mm (1/2 ") mango tipo espada

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

D
WALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286
E
(OCT05)
Form No. 637506-00
The following are trademarks for one or more D
"D" shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of
lozenge-shaped humps on the surface of the tool.
Important Safety Instructions
WARNING! Read all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury. The term "power tool" in all
of the warnings listed below refers to your mains-operated (corded) power tool or bat-
tery-operated (cordless) power tool.
READ ALL INSTRUCTIONS
Safety Instructions For All Tools
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence of
flammable liquids or gases.
• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For
example; pipes, radiators, ranges, and refrigerator enclosures.
• KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors should
be kept away from work area.
• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-up
place — out of reach of children.
• DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was intended.
• USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy-duty tool.
Don't use tool for purpose not intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving
parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear
protective hair covering to contain long hair.
be avoided.
• USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.
• DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. It's safer than using your hand and it
frees both hands to operate tool.
• DON'T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer perfor-
mance. Follow instructions for lubricating and changing accessories. Inspect tool cords peri-
odically and if damaged, have repaired by authorized service facility. Inspect extension cords
periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.
• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when chang-
ing accessories, such as blades, bits, cutters.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys
and adjusting wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch
is off when plugging in.
• EXTENSION CORDS. Use only 3-wire extension cords that have 3-prong grounding-type
plugs and 3-pole receptacles that accept the tool's plug. Replace or repair damaged cords.
Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating. The following table
shows the correct size to use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
DW131, DW132
Copyright © 2005 D
WALT power tools: the yellow and black color scheme; the
E
Air vents often cover moving parts and should also
Volts
120V
240V
Ampere Rating
More Not more
Than
Than
0 - 6
6 - 10
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you
are tired.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is dam-
aged should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or replaced by an authorized service cen-
ter unless otherwise indicated elsewhere in this instruction manual. Have defective switches
replaced by authorized service center. Do not use tool if switch does not turn it on and off.
Specific Safety Rules
• Hold tool by insulated gripping surfaces when performing an operation where the tool
may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts
of the tool "live" and shock the operator.
• Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.
• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
• Wear ear protectors when hammering for extented periods of time. Prolonged exposure
to high intensity noise can cause hearing loss. Temporary hearing loss or serious ear drum
damage may result from high sound levels generated by hammerdrilling.
• Wear safety goggles or other eye protection. Hammering and drilling operations cause
chips to fly. Flying particles can cause permanent eye damage.
• Always use the side handle supplied with the tool. Keep a firm grip on the tool at all
times. Do not attempt to operate this tool without holding it with both hands.
• Hammer bits and tools get hot during operation. Wear gloves when touching them.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other reproduc-
tive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
CAUTION: Wear appropriate hearing protection during use. Under some conditions
WALT
E
and duration of use, noise from this product may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V ..................volts
Hz ................hertz
min ..............minutes
............direct current
................Class II Construction
................safety alert symbol
Grounding Instructions
This tool should be grounded while in use to protect the operator from electric shock. The tool
is equipped with a 3-conductor cord and 3-prong grounding type plug to fit the proper ground-
ing type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire.
Never connect the green (or green and yellow) wire to a live terminal. If your unit is intended for
use on less than 150 V, it has a plug that looks like that shown in sketch A. If it is for use on 150
to 250 V, it has a plug that looks like that shown in sketch D. An adapter, sketches B and C, is
available for connecting sketch A type plugs to 2-prong receptacles. The green-colored rigid ear,
lug, or the like, extending from the adapter must be connected to a permanent ground, such as
a properly grounded outlet box. No adapter is available for a plug as shown in sketch D.
ADAPTER SHOWN IN FIGURES B and C IS NOT FOR USE IN CANADA.
A
GROUNDED
OUTLET
BOX
GROUNDING PIN
SAVE THESE INSTRUCTIONS
Motor
Your D
WALT tool is powered by a D
E
the nameplate marking. The markings; 120 volts, 50/60 Hz or "AC/DC", mean that your drill will
operate on alternating or direct current.Voltage decrease of more than 10% will cause loss of
power and overheating. All D
the power supply.
Spade Handle
The spade handle is installed as shown in Figure 1. Tighten the two screws securely.
NOTE: The spade handle can be removed from the tool if additional working clearance is need-
ed. Always operate drill with side handle or spade handle. Either handle may be removed but
never remove both handles at once!
Side Handle
CAUTION: Always use and hold the side handle or spade handle firmly . This is a high-
torque drill, always hold it with both hands when operating. The side handle screws into the
large hole in the top of the tool.
Switch
To turn the tool ON, depress the trigger switch. To turn the tool OFF, release the trigger switch.
(See Figure 2).
The toggle switch above the trigger is the reversing switch . Switch this toggle only when the
tool is not running or coasting. After reversing operations are completed, switch the toggle back
to forward position.
To lock the tool ON, depress the trigger and push in the lock button. Then, while holding the
lock button in position, gently release the trigger. To release locking mechanism, depress trig-
ger fully, then release it. Do not lock the switch ON when drilling by hand so that you can instant-
ly release the trigger switch if the bit binds in the hole. The locking feature is for use when the
Minimum Gage for Cord Sets
Total Length of Cord in Feet
0-25
26-50
51-100
0-50
51-100
101-200
AWG
18
16
16
18
16
14
A..............amperes
W ............watts
..........alternating current
n o ............no load speed
............earthing terminal
.../min ......revolutions per minute
B
C
GROUNDING
MEANS
ADAPTER
WALT built motor. Be sure your power supply agrees with
E
WALT tools are factory tested; if this tool does not operate, check
E
101-150
201-300
14
12
D
GROUNDING PIN

Publicidad

loading

Resumen de contenidos para DeWalt DW131

  • Página 1 WALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286 CAUTION: Wear appropriate hearing protection during use. Under some conditions (OCT05) Form No. 637506-00 DW131, DW132 Copyright © 2005 D WALT and duration of use, noise from this product may contribute to hearing loss.
  • Página 2 D WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1- 800-4-D WALT (1-800-433-9258) or visit our website www.dewalt.com. CAUTION: The use of any other accessory not recommended for use with this vacuum could be hazardous.
  • Página 3 • UTILISER L’OUTIL APPROPRIÉ. Ne jamais exiger d’un petit outil ou d’un accessoire le ren- CONSERVER CES MESURES. dement d’un outil de fabrication plus robuste. Se servir de l’outil selon l’usage prévu. Moteur • PORTER DES VÊTEMENTS APPROPRIÉS. Éviter de porter des vêtements amples et des bijoux qui peuvent être happés par les pièces en mouvement.
  • Página 4: Lea Todas Las Instrucciones

    Pour obtenir de plus amples renseignements sur les pièces ou les réparations cou- opere ninguna herramienta si está fatigado. vertes par la présente garantie, visiter le site www.dewalt.com ou composer le 1 800 433-9258 • VERIFIQUE LAS PARTES DAÑADAS. Antes de seguir empleando cualquier herramienta, (1 800 4-D WALT).
  • Página 5 Cualquier centro de servicio autor- tener otros dependiendo del estado o provincia en que se encuentre. izado DeWALT puede instalarle a su taladro un portabrocas sin llave en lugar del que tiene. Además de la garantía, las herramientas D WALT están cubiertas por:...

Este manual también es adecuado para:

Dw132