Master B 2IT Manual Del Usuario página 13

WARNING: Never use the heater without first assembling
all the components correctly (where applicable) and
making sure the heater is positioned on a perfectly flat,
stable and level surface.
►►6.1. SWITCH-ON:
►6.1.1. Connect the heater to the mains (Pic. 3).
►6.1.2. Turn the power selector to the desired mode (Pic.
4).
Here are the available settings:
•• By setting the power selector to "VENTILATION" the heat-
er will only operate in ventilation mode.
•• By setting the power selector to "I" the heater will operate
at heating power 1.
•• By setting the power selector to "II" the heater will operate
at heating power 2.
CAUTION: A SERIES OF SENSORS CHECK THAT THE
HEATER IS OPERATING CORRECTLY AND STOPS THE
APPLIANCE IN THE EVENT OF A SERIOUS FAULT. RE-
SETTING IS NOT AUTOMATIC, IT MUST BE PERFORMED
MANUALLY AFTER THE HEATER HAS COOLED DOWN
COMPLETELY. ELIMINATE THE POSSIBLE CAUSE OF
THE HEATER BLOCK (ES. OBSTRUCTED AN AIR VENT,
IMPAIRED THE AIR SUPPLY, ETC.) AND GENTLY PRESS
THE "RESET" BUTTON (Pic. 5) (if present). IF, AFTER A
FEW ATTEMPTS TO RESUME OPERATION, THE HEAT-
ER DOES NOT WORK, CONTACT THE SUPPORT CEN-
TRE.
►►6.2. SWITCH-OFF:
►6.2.1. Set the power selector to "0/OFF" (Pic. 6) and leave
the fan working until it comes to a complete stop.
►6.2.2. Disconnect the heater from the mains (Pic. 7).
CAUTION: FOR PROPER SWITCH-OFF, DO NOT DIS-
CONNECT THE HEATER FROM THE MAINS BEFORE
THE FAN HAS COMPLETELY STOPPED MOVING.
INCORRECT SWITCH-OFF MAY BLOCK THE PRODUCT.
TO UNLOCK THE HEART, GENTLY PRESS THE "RESET"
BUTTON (Pic. 5) (if present).
►►8. TROUBLESHOOTING
PROBLEM
The heater 1. Power selector set to "0/OFF"
doesn't work 2. Incorrect setting of the room
thermostat
3. No power supply
4. Blocked heater
The motor 1. Faulty motor
doesn't work 2. Blocked fan
The heater 1. Power selector set to "VENTILA-
doesn't heat TION"
2. Faulty internal appliance
Reduced 1. Obstructed air vent
airflow
2. Faulty motor
POSSIBLE CAUSE
►►7. STORAGE
Always disconnect the heater from the mains (Pic. 7), when
not in use and wait a few minutes for it to cool down com-
pletely before putting it away. Put it back in a dry place and
protected from dust. When the heater is used again, check
the condition of the power supply cable (where present); If in
doubt regarding its state, contact the support centre. In any
case, have the support centre check that the heater is work-
ing properly at least once a year and/or as required.
POSSIBLE SOLUTION
1. Turn the power selector to the desired mode
2. Make sure the temperature set on the room thermostat is
higher than the outdoor temperature
3a. Insert the power supply cable correctly
3b. Make sure your mains power supply is working correctly
3c. Contact the support centre
4a. Turn the heater back on by pressing the "RESET" button
4b. Contact the support centre
1. Contact the support centre
2a. Remove any obstructions
2b. Contact the support centre
1. Turn the power selector to the desired heating power
2. Contact the support centre
1a. Remove any obstructions
1b. Contact the support centre
2. Contact the support centre
en
it
de
es
fr
nl
pt
da
fi
no
sv
pl
ru
cs
hu
sl
tr
hr
lt
lv
et
ro
sk
bg
uk
bs
el
zh