Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

The featured mounting brackets are for use only with Smartspot™ Collision Avoidance System.
!
WARNING!
Failure to install or use this product according to manufacturers recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency safety devices are essential to ensure the safety of you and those you are
seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,which can cause personal injury and/or
severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this safety device. Install this product so that output performance of the system is maximized and the controls
are placed within convenient reach of the operator so that s/he can operate the system without losing eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment area may reduce the effectiveness
of the air bag or become a projectile that could cause serious personal injury or death. Refer to the vehicle owner's manual for the air bag deployment area. It is the responsi-
bility of the user/operator to determine a suitable mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator should ensure the projection of
the safety signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people, vehicles or other obstructions.
7. The use of this or any other safety device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-of way for granted. It is your respon-
sibility to be sure you can proceed safely before entering an intersection, driving against traffic
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding warning signal devices. Therefore,
the user should check all applicable city, state, and federal laws and regulations. The manufacturer assumes no liability for any loss resulting from the use of this safety
device.
INSTALLATION INSTRUCTIONS:
1. Loosely assemble the EZ1012 as shown in Figure 1. First attach the radar sensor to the silicone pad then attach to the sensor bracket
using two M4 screws, SS and nylon washers and M4 nuts. Attach this assembly to the horizontal pivot bracket using four M4 screws and
SS and nylon washers. Attach this assembly to the vertical pivot bracket using four M4 screws and nylon washers.
2. Position the assembly at the rear of the vehicle in the desired mounting location. Adjust the position of the radar sensor to make sure that
it can face in the correct orientation. Use the vertical pivot bracket as a template to mark the four mounting hole locations. Set the assem-
bly aside and pre-drill the mounting location holes (customer will supply mounting hardware - M4 hardware recommended).
3. Attach the assembly to the rear of the vehicle using the customer-supplied hardware. Pivot the assembly in the vertical pivot bracket up/
down to the desired orientation and tighten the two M4 screws on each side with a 3mm hex key. Pivot the assembly in the horizontal
pivot bracket left/right to the desired orientation and tighten the two M4 screws on the top and bottom with a 3mm hex key.
Installation and Operation Instructions
,
responding at a high rate of speed, or walking on or around traffic lanes.
*Sensor sold separately
Figure 1
EZ1012
Page 1 of 2

Publicidad

loading

Resumen de contenidos para Ecco EZ1012

  • Página 1 INSTALLATION INSTRUCTIONS: 1. Loosely assemble the EZ1012 as shown in Figure 1. First attach the radar sensor to the silicone pad then attach to the sensor bracket using two M4 screws, SS and nylon washers and M4 nuts. Attach this assembly to the horizontal pivot bracket using four M4 screws and SS and nylon washers.
  • Página 2 Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages. 833 West Diamond St, Boise, Idaho 83705 Customer Service USA 800-635-5900 UK +44 (0)113 237 5340 | AUS +61 (0)3 63322444 ECCOESG.com An ECCO SAFETY GROUP™ Brand ECCOSAFETYGROUP.com © 2020-ECCO Page 2 of 2 920-0882-00 Rev. B...
  • Página 3: Importante

    Instrucciones de instalación: 1. Monte el EZ1012 sin apretar, tal como se muestra en la Figura 1. Coloque primero el sensor de radar en la almohadilla de silicona y, a continuación, fíjelo al soporte del sensor con dos tornillos M4, arandelas de acero inoxidable y de nailon, y tuercas M4. Fije este conjunto al soporte de pivote horizontal con cuatro tornillos M4 y arandelas de acero inoxidable y de nailon.
  • Página 4 833 West Diamond St, Boise, Idaho 83705 Servicio Al Cliente EE.UU. 800-635-5900 Reino Unido +44 (0)113 237 5340 | AUS +61 (0)3 63322444 ECCOESG.com An ECCO SAFETY GROUP™ Brand ECCOSAFETYGROUP.com © 2020-ECCO 920-0882-00 Rev. B Pàgina 2 de 2...
  • Página 5 Instrucciones de instalación: 1. Assemblez l’EZ1012 sans le serrer, comme illustré à la Figure 1. Fixez d’abord le capteur radar au coussinet en silicone, puis fixez-le au support du capteur à l’aide de deux vis M4, de rondelles SS et nylon et d’écrous M4. Fixez cet ensemble au support de pivot horizontal à...
  • Página 6 à l’autre. Certaines juridictions ne permettent pas l’exclusion ou la limitation des dommages indirects ou consécu- tifs. 833 West Diamond St, Boise, Idaho 83705 Le Service Client États-Unis 800-635-5900 Royaume-Uni +44 (0)113 237 5340 | AUS +61 (0)3 63322444 ECCOESG.com An ECCO SAFETY GROUP™ Brand ECCOSAFETYGROUP.com © 2020-ECCO Page 2 sur 2 920-0882-00 Rév. B...