Frigidaire FES368DSC Manual Del Usuario

30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
INSTALLATION AND SERVICE MUST BE PERFORMED BY
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Do not pinch the power
supply cord between the
range and the wall.
Do not seal the range to the
side cabinets.
* NOTE: 24" (61 cm)
minimum clearance
between the cooktop and
the bottom of the cabinet
when the bottom of wood
or metal cabinet is
protected by not less than
1/4" (0.64 cm) flame
retardant millboard
covered with not less than
No. 28 MSG sheet metal,
0.015" (0.4 mm) stainless
steel, 0.024" (0.6 mm)
aluminum, or 0.020" (0.5
mm) copper.
30" (76.2 cm) minimum
clearance when the
cabinet is unprotected.
• Door Open
(see note)
B
• NOTE: Allow at least 19 ¼" (48.9 cm) clearance for
door depth when it is open.
A. HEIGHT
35 3/8" (90 cm) - 36 3/8" (92 cm)
G. Minimum cutout depth is increased to 24" (61 cm) with backguard.
A QUALIFIED INSTALLER.
NOTE:
For 29" (73.7 cm) cutout wide
opening, you must call for optional
side panels and clear wide cooktop
rim as shown in the "Countertop
Preparation" section (see page 6).
Shave Raised
Edge To Clear
1 ½" Max.
31 1/2"(81cm)
(3.8 cm Max.)
Wide Cooktop
Rim.
Locate Cabinet Doors
1" (2.5 cm) Min.
From Cutout Opening
C
1 5/16"
(3.3 cm)
21 3/4"
(55.25 cm)
A
C. DEPTH
B.WIDTH
TO FRONT
OF RANGE
30" (76,2 cm)
28 5/16" (71,9 cm)
(76.2 cm) Min.
30" Min.*
(76.2 cm) Min.*
F
H
G
Grounded Junction Box or Wall Outlet Should Be
Located 8" to 17" (20.3 - 43.2 cm) From Right
Cabinet and 2" to 4" (5.1-10.2 cm) From Floor
** For cutouts below
22 7/8"(58.1 cm),
appliance will
slightly show out
of the cabinet.
IMPORTANT
*** :
For width cutout (F dimension) more than 30 1/16"
(76.4 cm) to avoid glass breakage, make sure the
appliance is center in the counter opening. Raise
leveling legs at maximum position, insert the appliance
in the counter and then level. Make sure the unit is
supported by the leveling legs not by the smoothtop
glass itself.
F. CUTOUT
G. CUTOUT
WIDTH***
30 ± 1/16" 21 3/4" (55,2 cm) Min.
(76,2 ± 0,15 cm) 22 1/8" (56,2 cm) Max.
1
30" Min.
18" Min.
(45.7 cm) Min.
Approx. 1 7/8"
(4.8 cm)
24" Min.
(61 cm) Min.
22 7/8"**
(58.1 cm) min.
23 1/4"**
(59.05 cm) max.
1 1/8"
(2.86 cm)
G
Ref.
FRONT
OF
CABINET
H. HEIGHT
OF
DEPTH
COUNTERTOP
36" (91,4 cm) standard
35 3/8" (90 cm) min.
P/N 318201606 (0311) Rev. B
English – pages 1-9
Español – páginas 10-18
Français – pages 19-27
13"
(33 cm)