Idiomas disponibles
  • ES

Idiomas disponibles

Enlaces rápidos

4 IN 1
WORKSTATION
3500102 - Instruction Manual
USE PRECAUTION
INSTRUCTION
For your safety
MANUAL
Read and understand
RISK OF INJURY
EYE PROTECTION
PROTECTIVE GLOVES
Keep hands at a
Must be worn
Must be worn when
safe distance
handling tool
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
Safe operation of this accessory requires that you read and understand this manual
carefully before use.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Keep children away from this appliance.
Know your accessory. Read the operator's manual carefully. Learn its applications and
limitations, as well as the specific potential hazards related to this accessory.
If any parts are missing, do not use the stand until the missing parts are replaced.
NOTE This stand is designed for use with mitre saws and slide mitre saws with
mounting dimension not larger than 530mm.
NOTE Maximum weight of the mitre saw and workpiece together must not exceed
150 kg.
Do not modify or use this stand for any purpose for which it is not intended.
Always ensure the mitre saw used is mounted securely and is stable before plugging
in the mitre saw.
This stand is designed to be used on a flat, stable surface. Do not use the product on
an uneven or unstable surface. Be sure to allow enough room to handle and properly
support the workpiece.
Follow the tool mounting instructions carefully, and ensure the tool is fastened
securely.
To reduce the risk of injury from the mitre saw moving or falling off the stand, always
check that all mounting bolts and nuts are securely tightened before moving the
stand or using the tool.
Do not lift any part of the mitre saw that is attached to the stand.
When servicing, use only identical replacement parts. Use of any other parts may
create a hazard or cause product damage.
Save these instructions. Refer to them frequently and use them to instruct others who
may use this accessory.
ALWAYS KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents.
Make sure the floor is clean and not slippery due to wax or sawdust build-up.
CAUTION The assembly pack contains small parts which can pose a choking hazard
to children and pets.
EN
Tabla de contenido
loading

Resumen de contenidos para VonHaus 3500102

  • Página 40: Informacion De Seguridad

    INFORMACION DE SEGURIDAD TRABAJO 4 EN 1 INFORMACION DE SEGURIDAD IMPORTANTE 3500102 - Manual de Instrucciones La operación segura de este accesorio requiere que lea y comprenda este manual cuidadosamente antes de usarlo. Este aparato no debe ser utilizado por personas (incluidos niños) con capacidades físicas,...
  • Página 41: Componentes

    COMPONENTES Asegúrese de que todos los componentes estén presentes. Si falta algún componente, no proceda con el ensamblaje. Póngase en contacto con los servicios al cliente de DOMU Brands en hello@domu.co.uk Parte Descripción Cant. Soporte Mango M6 Tuerca M6x35 5 Rueda 6 Arandela 8 Arandela M8 Arandela de Resorte x8...
  • Página 42: Montaje

    MONTAJE ADVERTENCIA Ten cuidado. Existe la posibilidad de atraparse los dedos. Componentes necesarios para completar este paso de montaje. • Coloque la superficie superior del soporte (A) en el piso • Presione la palanca de bloqueo de pierna y levante la pierna hasta que la palanca haga clic en su lugar •...
  • Página 43 MONTAJE • Use la M6 Tuerca (C) and 6 Arandela (F) para ensamblar la 5 Rueda (E) al eje. Componentes necesarios para completar este paso de montaje. • Use el M6x35 Tornillo (D) y M6 Tuerca (C) para ensamblar el Mango (B).
  • Página 44 MONTAJE • Inserte el Tubo Tope (M) en la Base de Plástico (O) y ajustelo con los Tornillos (K) Componentes necesarios para completar este paso de montaje. • Adjunte el Soporte Central (N) al Tubo Tope (M) con los Tornillos (K)
  • Página 45 MONTAJE • Coloque la parte superior de trabajo ensamblada en el soporte y arréglela con las 4 capturas de bloqueo.
  • Página 46: Montaje Ajuste De Altura

    MONTAJE AJUSTE DE ALTURA • Apriete el botón dentro y tire del banco hacia arriba y hacia abajo para ajustarlo a la altura deseada. • Asegúrese de que el pasador de bloqueo se traba de forma segura a la nueva altura.
  • Página 47: Montaje De Una Sierra Ingleteadora En El Soporte

    MONTAJE DE UNA SIERRA INGLETEADORA EN EL SOPORTE Componentes necesarios para completar este paso de montaje (no suministrados) • Desenchufe la sierra y el brazo de la sierra en la posición hacia abajo. • Coloque un soporte de herramienta debajo de la sierra, alineando los orificios de montaje en la base de la sierra ingletadora con la ranura en la parte superior del soporte de la herramienta.
  • Página 48 MONTAJE DE UNA SIERRA INGLETEADORA EN EL SOPORTE • Use las manijas ubicadas en la parte posterior de la herramienta para ayudar a instalar o quitar el conjunto de la sierra y el soporte. • Levante la sierra y el conjunto de montaje de la herramienta, permitiendo que el conjunto se incline ligeramente hacia su cuerpo.
  • Página 49: Desmontaje De Una Sierra Ingleteadora En El Soporte

    DESMONTAJE DE UNA SIERRA INGLETEADORA EN EL SOPORTE • Levante las Palancas de bloqueo (J) para desbloquear la sierra y la herramienta de montaje • Sujete las manijas a cada lado del conjunto y levántelo del riel trasero del soporte para desengancharlo •...
  • Página 50 MONTAJE...
  • Página 51: Plegado Del Soporte

    PLEGADO DEL SOPORTE • Presione la palanca de bloqueo hasta que las patas estén completamente dobladas...
  • Página 52: Limpieza Y Mantenimiento

    Cualquier uso no autorizado puede violar los derechos de autor, marcas comerciales y otras leyes en todo el mundo. GRACIAS Gracias por comprar la estación de trabajo 5 en 1 VonHaus es una marca registrada de DOMU Brands Ltd Hecha en China para DOMU Brands Ltd M24 2RW.

Tabla de contenido