Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.
Important Safety Information
• Periodically check all components for tightness.
• Be sure to where safety goggles while installing.
• When using power tools, read and understand all operating instructions
Contents
Hardware List
8MM-30MM Hex Head Bolt Qty: 32
Door Latch Front: Qty 2
Door Latch Rear: Qty 2
Plastic Plug Cap: 4
Tools Required
13MM
Box Wrench
Pre-Installation Requirements
• Remove Factory Doors - We recommend that you roll down your windows prior to removing the factory doors.
Step 1 Front and Rear doors: Locate wiring harness along with limiting strap.
Step 2 Unplug the wiring harness 3 connector under the instrument panel by pressing the tab at the top of the connector 1 and pulling to
disconnect. NOTE: If the red latch on the connector is locked, pull the red latch down. This will unlock the connector tab, allowing the tab
to be pressed down and enabling the harness to be disconnected.
Step 3 Locate the 2 hex bolts that are used to attach the factory door to the hinge. Use a T-50 TORX bit to remove the hex bolts. Once the
bolts are removed you can remove the door. Unhook the limiting strap 2, carefully lift the door out of the hinges. Be careful as the doors
are a bit heavy. Reattach the hex bolts on the doors, that way they wont get lost. Repeat this process for the other doors.
Installation Instructions
TrailView Tube Half Doors
For proper installation and best possible fit, please read all instructions BEFORE you begin.
8.5MM large flat washers Qty: 24
Upper door pins Qty: 4
Tube Half Door Front: Qty 2
13MM
Ratchet and extensions
8M hex nut: 40
Lower door pins Qty: 4
Tube Half Door Rear: Qty 2
T-50
Torx Bits
Page 1 of 4
I-TD-01 Rev. C
WARNING!
Do not drive your vehicle on public roads with the
doors removed as you will lose the protection that
they can provide. This procedure is furnished for use
during o -road operation only
8MM Lock Washer Qty: 20
8MM flat washers Qty: 12
Mirror Stand-off top (51mm): Qty 2
Mirror Stand-off bottom (61mm): Qty 2
Safety Glasses

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Rampage TrailView Tube Half Doors

  • Página 5: Lista De Componentes

    I-TD-01 Rev. C ™ TrailView Tube Half Doors Para obtener una instalación correcta y el mejor ajuste posible, lea las instrucciones ANTES de comenzar. Para pedir asistencia técnica u obtener piezas que falten, llame a Atención al cliente al 1-800-241-7219.
  • Página 6: Pasos Para La Instalación

    Pasos para la instalación NOTA: La aplicación real puede ser mínimamente diferente de las ilustraciones. Ubicación de la correa de puerta/el arnés Desconecte el conector del arnés eléctrico bajo el panel de instrumentos al presionar la pestaña en la parte superior del conector y tirar para desconectar.
  • Página 7 Pasos para la instalación Nota: La manija del pestillo de la puerta delantera orientada con la parte superior hacia arriba. Nota: La manija del pestillo de la puerta delantera orientada con la parte superior hacia arriba. Conjunto de puerta trasera en un cuatro puertas Consejo: Alinee la traba del pestillo de la puerta antes de ajustar.
  • Página 8: Cuidado Y Limpieza

    Sus nuevas TrailView Tube Doors™ ya están instaladas. Ahora, disfrute del paseo. Gracias por adquirir un artículo de la amplia variedad de productos de calidad Rampage® que ofrece Lund International, Inc. Estamos sumamente orgullosos de nuestros productos y esperamos que disfrute de años de satisfacción por su inversión. Hemos hecho grandes esfuerzos para garantizar que su producto sea de la mejor calidad en cuanto al ajuste, la durabilidad, el acabado y la facilidad de instalación.

Tabla de contenido