Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Read, Understand, Follow and Save These Instr uctions
Read, understand and follow all of these instructions and warnings (Instructions) before installing and using this product. Install and use this product
only as specified in these instructions. Improper installation or use of this product may result in property damage, serious injury, and/or death. Never
allow installation or use of this product by anyone without providing them with these instructions. You must read, understand and follow all instructions
and warnings for any product(s) to which this product is used in conjunction with or installed. Save these instructions with the product for use as a
reference for any future installation and use of the product.
WARNING
• Purchaser/owner must ensure that product is
installed according to these instructions. Pur-
chaser/owner must not alter or modify product.
• Operator and bystanders should never position
any part of body under any portion of this prod-
uct or the load being supported.
RF-24C Wireless Remote Control
DC
for
Winches and Jacks
P/N 500526 6-Pin Wireless
Remote Control Kit includes:
1. Wireless Receiver
2. Switch Cord W/6Pin plug Ø8 X 1500 mm
3. Wireless Transmitter
4. Lithium Battery: 3V CR2032
5. Transmitter Strap
P/N 500527 3-Pin Wireless
Remote Control Kit includes:
1. Wireless Receiver
2. Switch Cord W/3Pin plugs Ø8 X 1500 mm
3. Wireless Transmitter
4. Lithium Battery: 3V CR2032
5. Transmitter Strap
I. Specifications
1. Transmission range:15 ~ 27 m (50 ~ 90 ft)
2. Receiver operation voltage: 8 ~ 24 V
3. Receiver fuse current rating: 7.5 A
4. Protection: IP-66
5. Operating temperature range: -20°C ~ +70°C
6. LED indication: Green light for power on; Red light for operating; Blinking green for low battery life;
Blinking red light for poor signal received
II. Installation
Step 1: Connect the wiring
Connect the Switch cord W/3 or 6 Pin plugs to the socket on the control pack.
Connect the Red wire to the positive (+) terminal of the battery.
Connect the Black wire to the negative (-) terminal of the battery.
Failure to follow these warnings and instructions may result
in property damage, serious bodily injury, and/or death.
• Do not allow children to play on or around this
product or the load being supported.
• Never exceed maximum rated capacity. Refer to
stamped markings or decals on product to obtain
rated capacity. If uncertain, contact Cequent
Performance Products at 1-800-632-3290 or
Know Your Remote
1.
3.
Installation Instr uctions
Installation Instructions
www.cequentgroup.com
• Never lose sight of the winch or jack while using
the wireless remote.
• Never touch the winch or jack while the remote
is in someone else's hands.
2.
4.
LED indication
5.
F3867 (revA-3709) 1/15
Tabla de contenido
loading

Resumen de contenidos para FULTON PRO Serie

  • Página 4: Control Remoto Inalámbrico Rf- 24C Para Cabrestantes Y Gatos Dc

    Instrucciones de Instalación Lea, comprenda, siga y guarde estas instr ucciones Lea, entienda y siga todas estas instrucciones y advertencias (instrucciones) antes de instalar y usar este producto. Instale y use este producto únicamente según se especifica en estas instrucciones La instalación o uso incorrecto de este producto podría resultar en daños a la propiedad, lesiones graves y/o la muerte.
  • Página 5: Operación

    Instr ucciones de instalación Fusible Rojo Fusible Rojo Negro Negro Paso 2: Monte el Receptor El receptor debe ser montado en una ubicación despejada y seca. Móntelo en una superficie plana con por lo menos dos tornillos pasadores (los cuales no están incluidos) a través de los agujeros de montaje de 7 mm en cada Un mínimo de un tornillo pasador en lado del receptor.
  • Página 6: Cómo Ordenar El Producto

    Bulldog® y Fulton®, y un año para los productos de Pro-Series®, excepto por el uso y desgaste normal; siempre y cuando la instalación y el uso del producto esté...

Este manual también es adecuado para:

Rf24c500526500527

Tabla de contenido