Ingersoll Rand S80 Manual De Funcionamiento

OPERATION AND MAINTENANCE MANUAL
FOR MODEL S80 CIRCULAR AIR SAW
TPD1722
The Model S80 Air Circular Saw, when used with the proper blade, can be used by contractors to cut
concrete, granite, heavy sections of aluminum, steel tubing, timbers, planking, etc. Because there
are no electrical cables, these saws are ideally suited for shipyard work and wet environments.
Ingersoll–Rand is not responsible for customer modification of tools for applications on which
Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE
THE INFORMATION IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
•
Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code for Portable Air Tools
(ANSI B186.1).
•
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the inlet
with 3/4" (19 mm) inside diameter air supply hose.
Operating at higher air pressure will result in
excessive speed and may result in injury.
•
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
•
Do not use damaged, frayed or deteriorated air
hoses and fittings.
•
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
•
Always use clean, dry air. Dust, corrosive fumes
and/or excessive moisture can ruin the motor of an
air tool and affect performance.
•
Use only lubricants recommended by
Ingersoll–Rand. Do not lubricate tools with
flammable or volatile liquids such as kerosene,
diesel or jet fuel.
•
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
•
Always wear eye protection when operating or
performing maintenance on this tool.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 1999
Printed in U.S.A.
03530268
•
Always wear hearing protection when operating
this tool.
•
Use other personal protective equipment such as
gloves, apron and helmet when necessary.
•
Keep hands, loose clothing and long hair away from
rotating end of tool.
•
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
•
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
•
Tool accessories may continue to rotate briefly after
throttle is released.
•
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Always release throttle in case of energy supply
failure.
•
Use accessories recommended by Ingersoll–Rand.
•
Do not use in explosive atmospheres or on explosive
or flammable materials.
•
Do not cut into electrical cables. This tool is not
insulated against contact with electric power
sources.
•
This tool is not designed for working in explosive
atmospheres.
•
This tool is not insulated against electric shock.
F
Form P6495
Edition 8
E
October, 1999
P