Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Proper use of the tool
Do not use the tool outside its design intent.
Never modify the tool for any other purpose than
its intended function.
• Normal use of this product is likely to
expose the user to dust and/ or microscopic
particles containing chemicals known to the
state of California to cause cancer, birth
defects or other reproductive harm. Always
wear appropriate safety equipment and
clothing when using this product. Study,
understand and follow all instructions
provided with this product.
• Always wear ANSI approved goggles
when using this product
• Always use the correct accessories for
the job that you are performing.
• Always work in a clear, safe, well-lit,
organized and properly equipped area.
• NEVER begin repairs without ensuring that
vehicle is in secure position and will not
move during repair.
Product Information:
• High volume low pressure for greater transfer efficiency
• Full range of viscosities from fine surface finish
to heavy body coating
• Comes with one pint nylon cup with "drip check" device
to prevent spillage from the vent hole
• Unibody head construction
SPECIFICATIONS:
Nozzle Size:
Cup Capacity:
Operation Pressure:
Weight:
Dimensions W x H:
Avg. Air Consumption:
Air Inlet Thread NPT:
Required Compressor:
Max. Pattern at 8" Distance:
Air Cap Output:
Air Hose I.D. Size:
Important
Read these instructions carefully before
installing, operating, servicing or repairing this tool.
Keep these instructions in a safe accessible place.
MTPGHV13
MODEL:
MTPGHV15
MTPGHV17
MTPGHV19
1.3mm, 1.5mm, 1.7mm, 1.9mm
600ml
29psi
1.1lbs. (518g )
6" x 13-1/2"
10cfm
1/4"
3hp
9-10-1/2" (203-265mm)
10psi
4-6mm
1.3 mm
Product Type:
1.5 mm
GRAVITY FEED HVLP
1.7 mm
SPRAY GUN
1.9 mm
1 YEAR LIMITED WARRANTY
The manufacturer warrants this product to the original user against
defective material or workmanship for a period of 1 year from the
date of purchase.
The
manufacturer reserves the right to determine whether the part
or parts failed because of defective material, workmanship or other
causes. Failures caused by accident, alteration, or misuse are not
covered by this warranty.
The manufacturer, at its discretion, will repair or replace product
covered under this warranty free of charge. Repairs or
ments of products covered under this warranty are warranted for
the remainder of the original warranty period.
The
manufacturer or its authorized service representatives must
perform all warranty repairs. Any repair to the product by
ized service representatives voids this warranty. The rights under
this warranty are limited to the original user and may not be
transferred to subsequent owners.
The
warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular
purpose. Some states do not allow the exclusion or limitations of
incidental or consequential damages, so the above limitations may
not apply to you.
When unpacking, check the parts diagram and part number listing
on page 6 to make sure all parts are included. If any parts are
missing or damage, please call your distributor immediately.
GRAVITY FEED HVLP SPRAY GUN
Page 1
WARNING
Unpacking
replace-
unauthor-

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Matco Tools MTPGHV13

  • Página 1 MTPGHV13 1.3 mm Product Type: MODEL: MTPGHV15 1.5 mm GRAVITY FEED HVLP MTPGHV17 1.7 mm SPRAY GUN MTPGHV19 1.9 mm Proper use of the tool Do not use the tool outside its design intent. Never modify the tool for any other purpose than its intended function.
  • Página 2 MTPGHV13 1.3 mm Product Type: MODEL: MTPGHV15 1.5 mm GRAVITY FEED HVLP MTPGHV17 1.7 mm SPRAY GUN MTPGHV19 1.9 mm Instruction Your new MATCO Spray Gun has been manufactured with precision machinery and is constructed to perform under demanding professional requirements. To ensure maximum efficiency and best painting results, knowledge of the components and proper handling and maintenance is essential.
  • Página 3 MTPGHV13 1.3 mm Product Type: MODEL: MTPGHV15 1.5 mm GRAVITY FEED HVLP MTPGHV17 1.7 mm SPRAY GUN MTPGHV19 1.9 mm SPRAY GUN HANDLING Coating will Coating will be light be heavy To obtain its optimal result, proper handling is essential.
  • Página 4: Troubleshooting

    MTPGHV13 1.3 mm Product Type: MODEL: MTPGHV15 1.5 mm GRAVITY FEED HVLP MTPGHV17 1.7 mm SPRAY GUN MTPGHV19 1.9 mm TROUBLE SHOOTING Pattern Cause Correction • Uneven air pressure from side-holes • Use a thinner to dissolve obstructions; due to dried material blow the gun clean afterwards •...
  • Página 5: General Maintenance

    MTPGHV13 1.3 mm Product Type: MODEL: MTPGHV15 1.5 mm GRAVITY FEED HVLP MTPGHV17 1.7 mm SPRAY GUN MTPGHV19 1.9 mm GENERAL MAINTENANCE Spray Gun PRECAUTIONARY NOTE 1. Immerse only the front end of the MATCO Spray gun All parts on the MATCO Spray Gun should be hand until solvent just covers the fluid connection.
  • Página 6: Parts Breakdown

    MTPGHV13 1.3 mm Product Type: MODEL: MTPGHV15 1.5 mm GRAVITY FEED HVLP MTPGHV17 1.7 mm SPRAY GUN MTPGHV19 1.9 mm PARTS BREAKDOWN Optional Use Regulator (not included) Parts List for best performance and increased efficiency. INDEX INDEX PART NO. DESCRIPTION QTY.
  • Página 7: Mesure De Sécurité

    MTPGHV13 Type de produit : 1.3 mm MODÈLE: MTPGHV15 1.5 mm PISTOLET PULVÉRISATEUR MTPGHV17 1.7 mm HVLP À GRAVITÉ MTPGHV19 1.9 mm Utilisation prévue Utiliser uniquement cet outil pour l’usage pour lequel il a été conçu. Ne jamais modifier l’outil pour un but autre que sa fonction d’origine prévue.
  • Página 8 MTPGHV13 Type de produit : 1.3 mm MODÈLE: MTPGHV15 1.5 mm PISTOLET PULVÉRISATEUR MTPGHV17 1.7 mm HVLP À GRAVITÉ MTPGHV19 1.9 mm Instructions Votre nouveau pistolet à peinture a été fabriqué par des machines de précision et conçu pour fournir des résultats répondant aux exigences professionnelles.
  • Página 9 MTPGHV13 Type de produit : 1.3 mm MODÈLE: MTPGHV15 1.5 mm PISTOLET PULVÉRISATEUR MTPGHV17 1.7 mm HVLP À GRAVITÉ MTPGHV19 1.9 mm MANIPULATION DU PISTOLET Le revêtement le revêtement sera léger sera épais Pour obtenir un résultat optimal, une en ce point en ce point manipulation adéquate est essentielle.
  • Página 10: Incidents Possibles

    MTPGHV13 1.3 mm Type de produit : MODÈLE: MTPGHV15 1.5 mm PISTOLET PULVÉRISATEUR MTPGHV17 1.7 mm HVLP À GRAVITÉ MTPGHV19 1.9 mm INCIDENTS POSSIBLES Description Cause Solution • Pression de l'air non uniforme à partir • Utiliser un diluant pour dissoudre les obstructions, des trous latéraux causée par...
  • Página 11: Entretien General

    MTPGHV13 1.3 mm Type de produit : MODÈLE: MTPGHV15 1.5 mm PISTOLET PULVÉRISATEUR MTPGHV17 1.7 mm HVLP À GRAVITÉ MTPGHV19 1.9 mm ENTRETIEN GENERAL Pistolet Pulverisateur MISE EN GARDE 1. Immerger seulement l'extrémité frontale du Pistolet Toutes les pièces du Pistolet Pulvérisateur MATCO devraient être Pulvérisateur MATCO jusqu'à...
  • Página 12 MTPGHV13 1.3 mm Type de produit : MODÈLE: MTPGHV15 1.5 mm PISTOLET PULVÉRISATEUR MTPGHV17 1.7 mm HVLP À GRAVITÉ MTPGHV19 1.9 mm PARTS BREAKDOWN Optional Use Regulator (not included) Parts List for best performance and increased efficiency. INDEX INDEX PART NO.
  • Página 13: Pistola Para Pintar Hvlp Con Alimentación Por Gravedad

    MTPGHV13 1.3 mm Tipo de producto: MODELO: MTPGHV15 1.5 mm PISTOLA PARA PINTAR HVLP CON MTPGHV17 1.7 mm ALIMENTACIÓN POR GRAVEDAD MTPGHV19 1.9 mm Uso previsto de la herramienta Use esta herramienta exclusivamente para el fin que fue diseñada. Nunca modificar la herramienta por cualquier otro motivo que no sea la función programada.
  • Página 14: Instrucción

    MTPGHV13 1.3 mm Tipo de producto: MODELO: MTPGHV15 1.5 mm PISTOLA PARA PINTAR HVLP CON MTPGHV17 1.7 mm ALIMENTACIÓN POR GRAVEDAD MTPGHV19 1.9 mm Instrucción Su nueva Pistola Rociadora MATCO ha sido manufacturada con máquinas de precisión y viene construida para trabajar de acuerdo con exigentes requisitos profesionales. Para asegurar la máxima eficiencia y el major resultado de pintura, es esencial conocer bien las maneras de manejar y mantener los componentes.
  • Página 15: Manipulación De La Pistola

    MTPGHV13 1.3 mm Tipo de producto: MODELO: MTPGHV15 1.5 mm PISTOLA PARA PINTAR HVLP CON MTPGHV17 1.7 mm ALIMENTACIÓN POR GRAVEDAD MTPGHV19 1.9 mm MANIPULACIÓN DE LA PISTOLA La capa será de La capa será baja densidad de alta densidad...
  • Página 16: Tipo De Producto

    MTPGHV13 1.3 mm Tipo de producto: MODELO: MTPGHV15 1.5 mm PISTOLA PARA PINTAR HVLP CON MTPGHV17 1.7 mm ALIMENTACIÓN POR GRAVEDAD MTPGHV19 1.9 mm LOCALIZACIÓN DE FALLAS Patrón Causa Corrección • Presión de aire despareja de los agujeros • Usar solvente para disolver obstrucciones,...
  • Página 17: Mantenimiento General

    MTPGHV13 1.3 mm Tipo de producto: MODELO: MTPGHV15 1.5 mm PISTOLA PARA PINTAR HVLP CON MTPGHV17 1.7 mm ALIMENTACIÓN POR GRAVEDAD MTPGHV19 1.9 mm MANTENIMIENTO GENERAL Pistola Atomizadora NOTA PREVENTIVA 1. Sumergir sólo la parte frontal de la Pistola Atomizadora MATACO Todas las partes en la Pistola Atomizadora MATCO deben estar hasta que el solvente cubra la conexión del fluido.
  • Página 18 MTPGHV13 1.3 mm Tipo de producto: MODELO: MTPGHV15 1.5 mm PISTOLA PARA PINTAR HVLP CON MTPGHV17 1.7 mm ALIMENTACIÓN POR GRAVEDAD MTPGHV19 1.9 mm PARTS BREAKDOWN Optional Use Regulator (not included) Parts List for best performance and increased efficiency. INDEX...

Este manual también es adecuado para:

Mtpghv15Mtpghv17Mtpghv19

Tabla de contenido