Descargar Imprimir esta página

Echo 99988802000 Instrucciones De Instalación

Protectores de puntas de cortaseto

Publicidad

Enlaces rápidos

Kit Contents:
99988802000 – (for use with HC-150, HC-155, SHC-225, SHC-225S, SHC-265) tip guard, 2 bolts, 1 nut,
1 flange nut, 2 flat washers
99988802010 – (for use with HCA-265) tip guard, 2 bolts, 1 nut, 1 flange nut, 2 flat washers
99988802020 – (for use with HC-225, 235, 245) tip guard, bolt, nut, flat washer
99988802030 – (for use with HC-165, 185) tip guard, 2 bolts, 1 nut, 1 flange nut, 2 flat washers
Instructions:
WARNING
Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid touching
blades whenever possible, and always wear gloves to protect hands.
1. Remove spark plug lead.
2. Remove blade bolt and nut (and washer, if applicable) farthest
from engine.
IMPORTANT
NOTE Hardware combination and configuration. New bolt will be
longer than bolt removed from unit.
3. Select identical new bolt/nut/washer combination from kit con-
tents and secure tip guard onto support bar. Install hardware in
original configuration.
IMPORTANT
Bolt must be installed into correct hole in tip guard so that tip
guard does not contact blades and sits flat against support bar.
4. Adjust and lubricate blades according to instructions in your operator's manual.
5. Attach spark plug lead.
Contenido de los juegos:
99988802000 – (para usar con HC-150, HC-155, SHC-225, SHC-225S, SHC-265) protector de punta,
2 pernos, 1 tuerca, 1 tuerca embridada, 2 aran delas planas
99988802010 – (para usar con HCA-265) protector de punta, 2 pernos, 1 tuerca, 1 tuerca embridada, 2 aran
delas planas
99988802020 – (para usar con HC-225, 235, 245) protector de punta, perno, tuerca, arandela plana
99988802030 – (para usar con HC-165, 185) protector de punta, 2 pernos, 1 tuerca, 1 tuerca embridada, 2
arandelas planas
Instrucciones:
ADVERTENCIA
Las hojas del cortasetos están muy afiladas. El contacto
con las mismas puede producir lesiones personales gra-
ves. No toque las hojas siempre que sea posible, y lleve
siempre puestos guantes para protegerse las manos.
X7672240101
HC T
G
ip
i
nsTruCTions
insTruCCionEs dE insTalaCiÓn dE los
p
roTECTorEs dE punTas dE CorTasETos
i
uard
nsTallaTion
X767000271
05/10

Publicidad

loading

Resumen de contenidos para Echo 99988802000

  • Página 1 Kit Contents: 99988802000 – (for use with HC-150, HC-155, SHC-225, SHC-225S, SHC-265) tip guard, 2 bolts, 1 nut, 1 flange nut, 2 flat washers 99988802010 – (for use with HCA-265) tip guard, 2 bolts, 1 nut, 1 flange nut, 2 flat washers 99988802020 –...
  • Página 2 GardE anTi rEbond Contenu du kit : 99988802000 – (pour HC-150, HC-155, SHC-225, SHC-225S, SHC-265) garde anti rebond, 2 boulons, 1 écrou, 1 écrou à embase, 2 rondelles plates 99988802010 – (pour HCA-265) garde anti rebond, 2 boulons, 1 écrou, 1 écrou à embase, 2 rondelles plates 99988802020 –...

Este manual también es adecuado para:

999888020109998880202099988802030