NSS CXC 200 Manual Del Usuario página 3

FIG G. 3: Top p Detail
Control
panel
Heat t Switch (hea ated units only
solut tion heater. H eated units a
powe er cord. The s second power
to a s separate elec ctric power so
Pres ssure regulat tor (Fig. 2, G)
only . Turn clockw wise to increas
coun terclockwise to decrease s
Auto o pump-out s switch (Fig. 2
Switc ch to ON posi ition to activa
CXC C 200, CX H 200, & C
OPE ERATING INSTRUC
1. P Pre-mix clean ning solution w
s separate cont tainer. Pour m
solution tank o s of the machin
IMPO ORTANT: Foa am in the reco
mois sture, carpet fi fiber and othe
the v vacuum system m. Use a low
defoa amer to the re ecovery tank
defoa amer manufa cturer instruc
appli ication. Dama age caused by
void the product w warranty.
2. C Connect vacu uum and solut
a attach to extra action wand o
3. I nsert both co rds into sepa
outlets on sep o parate circuits
c cleaning path .
4. S Select vacuum m control - on
5. T Turn on soluti on pump. * S
6. If f desired, turn n on heater (H
Manual l 4092471 (Rev. 1120 011)
Cord
wrap
Solu ution
tank k fill
hole e
y). Turns on t he in-line
re equipped w with a second
r cord must be e plugged in
ource.
). 500 and 12 200 models
se solution pr ressure; turn
solution press sure.
2, E) CXC 120 00 only.
te auto pump p-out mode.
CXH 500
CTIONS
with hot water r in a
mixed solution n into the
ne.
overy tank ca an allow
r debris to be e drawn into
w-foam deterg ent. Add a
if foaming oc curs. Follow
ctions for prop per
y moisture or r debris will
tion hoses to machine and
or hand tool.
rate, 3-prong grounded
s. Keep cords clear of your
ne or two vacu uums.
See NOTICE, below.
H units only).
7. Begin cleanin
procedures.
8. Solution pres
with the pres
the pressure
CAU UTION: When
an a automatic flo
Fig. . 7) and the v
pitc ched noise. W
be t turned off im
vac uum motors
9. When the job
liquid from th
ensure no de
tank.
d
10. Empty and ri
help to preve
and reduce t
11. Turn on both
for 3–5 minut
the vacuum m
NOT TICE: At time
prim ming in order
pum mp, insert the
in th he rear pock
the solution hos
solu ution tank an
mom ments, the p
whe en steady wa
use e.
For maintenance
TIP: : To empty th
hose e from wand
tank k.
F FIG. 4:
S Solution Pump
f filter location.
R Rinse clean af
e each use.
r
3
ng. Follow ind dustry-approv
ssure on the C CXH 500 may
ssure regulato or knob (Fig. 2
gauge to ens sure pressure
n the recove ery tank reac
oat valve blo cks vacuum
vacuum moto ors will make
When this oc ccurs, the ma
mmediately to o prevent dam
s.
b is complete , vacuum out
he solution tan nk. Rinse with
etergents or r inse agents r
nse the waste e tank thorou
ent the format tion of damag
he growth of odor-causing
h vacuum mot tors and allow
tes to help re emove any mo
motors and a ssure long va
es the soluti on pump ma
r to operate properly. To
e male quick k-connect fitt
ket of the uni t) into the wa
se. Place the e end of the h
nd start the p pump. After a
ump will dis charge exce
ater flow exis sts, the unit
e instructions, see "Mainten
he solution tan nk, remove th
and extract th he solution fro
p
.
fter
ved
y be adjusted
2, G). Monitor r
e is adequate .
hes capacity y,
intake (see
e a high
achine shoul ld
mage to the
any remainin ng
h clear water to
emain in the
ughly. This wil l
ging deposits
g bacteria.
w them to run
oisture from
acuum life.
ay require
o prime the
ting (shipped d
and end of
hose into the e
a few
ess air and
is ready for
nance," p. 5.
he vacuum
om solution