Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property damage, serious bodily/
personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.
1. Proper installation combined with operator training in the use, care and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current
arcing, which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system
without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, drive
against traffic, respond at a high rate of speed, or walk on or around traffic lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations.
The manufacturer assumes no liability for any loss resulting from the use of this warning device.
8. This product may contain high intensity LEDs. Staring directly into these lights could result in temporary and/or permanent vision
impairment.
Specifications:
Weight:
Input Voltage:
Input Current:
Output Power:
Fusing Requirement:
Matrix
Connectivity:
®
Operating Temperature:
Installation and Operation Instructions
5.1lbs
12-24 VDC
6.8 A max.
87.0 W max.
10A
CAT5
-40ºC to 65ºC
(-40ºF to 149ºF)
Thin SuperVisor Series
MATRIX
Enabled
®
Page 1 of 8

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Code 3 Thin SuperVisor Serie

  • Página 9: Especificaciones

    Instrucciones de instalación y operación Serie Thin SuperVisor MATRIX activado ® ¡IMPORTANTE! Lea todas las instrucciones antes de instalar y utilizar. Instalador: Este manual se debe entregar al usuario final. ADVERTENCIA Si este producto no se instala o se utiliza de acuerdo con las recomendaciones del fabricante, esto podría tener como resultado daños a la propiedad, lesiones graves o la muerte de las personas que se busca proteger.
  • Página 10: Desembalaje Y Preinstalación

    Retire el producto con cuidado y colóquelo sobre una superficie plana. Examine la unidad en busca de daños que se hayan producido en el transporte y localice todas las piezas. Si encuentra algún daño, o faltan piezas, comuníquese con la empresa de transporte o Code 3. No utilice piezas dañadas o rotas.
  • Página 11: Instrucciones De Cableado

    Instrucciones de cableado: ¡IMPORTANTE! Esta unidad es un dispositivo de seguridad y se debe conectar a su propia fuente de poder de fusibles separada para asegurar su funcionamiento continuo si cualquier otro accesorio eléctrico falla. No cablee en paralelo con ningún otro accesorio. Notas: •...
  • Página 12: Piezas De Repuesto

    La red Matrix está diseñada para alojar un gran número de dispositivos accesorios. Sin embargo, un Thin SuperVisor compatible con ® Matrix que utilice CAT5 siempre será el último dispositivo en la cadena PRI-1 o SEC-2. En el manual de instalación del "nodo central" ®...
  • Página 13: Solución De Problemas

    Solución de problemas: Todas las barras de luces se prueban a fondo antes de su envío. Sin embargo, si se produce un problema durante la instalación o durante la vida útil del producto, siga la guía que aparece a continuación para obtener información sobre la solución de problemas y la reparación. Si el problema no se puede solucionar con las soluciones que se indican a continuación, puede obtener información adicional del fabricante;...
  • Página 14 Notas: Página 6 de 8...
  • Página 15 Notas: Página 7 de 8...
  • Página 16: Exclusión De Otras Garantías

    Asegúrese de utilizar suficientes materiales de embalaje para evitar que se dañe el producto durante el envío. * Code 3®, Inc. se reserva el derecho a realizar reparaciones o reemplazar productos según su criterio. Code 3®, Inc. no asume responsabilidad alguna por los gastos efectuados para remover o reinstalar los productos que requieren servicios o reparaciones, por el embalaje, la manipulación y el envío ni por la manipulación de los productos devueltos al remitente después de que se haya prestado el servicio.

Tabla de contenido