Eaton Greengate ControlKeeper 4A CK4A-SSRC Instrucciones De Instalación

Installation Instructions
ControlKeeper® 4A
General Information
The ControlKeeper 4A model is shipped in one package
and is configured with a dual tapped 120V/277V/347V
60 Hz or 230V/240V 50 Hz transformer. It can be
configured with different relay types as needed to achieve
lighting needs. Please refer to your order information to
determine which model you have purchased.
The ControlKeeper 4A can control up to four relays per
panel with optional support for up to four 0-10V dimming
control outputs to allow for combinations of relay
switching and load dimming.
Getting Started
1. Do not discard these installation instructions. Please
keep for future reference and operation information.
2. Always disconnect all power before wiring.
3. Use only as intended and at the listed voltage.
4. All installation and service must be performed by
qualified personnel or service technicians.
5. Install in accordance with the National Electrical Code
and any other codes which may apply.
6. Installation and wiring information contained in this
document is based on industry-accepted standards
and practices. If conflicts exist between these
instructions and any applicable codes or ordinances,
please contact Greengate before proceeding with the
installation.
7 . High voltage is present inside the enclosure. Use
extreme caution when performing maintenance on
this equipment. Failure to follow this warning and
proper safety procedures could result in severe injury
or death, and/or damage to the equipment.
8. Document all wiring and device terminations and
locations so that devices can be properly configured
and programmed for operation.
Model# CK4A-SSRC
Model# CK4A-SLRC
Model# CK4A-STPRC
Mounting the Cabinet
1. Choose a dry location on a firm surface convenient to
the circuits being controlled. Allow full clearance for
the door of the enclosure to open fully.
2. Mount the ControlKeeper 4A cabinet using the holes
provided in the back of the enclosure.
3. All line voltage conductors must enter the cabinet on
the right side of the enclosure.
4. All low voltage conductors must enter the cabinet on
the left side of the enclosure.
5. Remove all debris and metal shavings from
the enclosure before applying power to the
ControlKeeper 4A.
N ote: Make certain that high voltage and low voltage
wiring enters the enclosure separately. Failure to
separate high voltage from low-voltage wiring may
cause interference with functionality. High Voltage
wiring should not be brought into the enclosure
through the left side of the enclosure.
Low voltage wiring can be brought into the enclosure
from the bottom left or upper left of the enclosure. Due
to limited space on the left side of the enclosure, it is
recommended that connections be brought through the
top or bottom of the enclosure for the low-voltage wiring.
Bring Low Voltage in
through the Left Side of
the Enclosure
Figure 1: ControlKeeper-4 Enclosure
INS #
Bring High Voltage in
through the Right Side
of the Enclosure
50-022510-02
LED1 ADDRESS 54-022510-
NETWORK ALL OFF LED2 ALL ON LED3 1 3 2 4 5 6 7 8
J1 Reset
SW1
SW1 SW2 SW3
CAN-RX CAN-TX H1
LED4 LED5
J2
U1 U2
J3
U5 U6
L1 L2 L3 L4
J4
U7 J5
TB1
C20
PS1
U8 LED6
RSC STAT SR1
U9 L1
J6
PCI-NET TERM
S1
U10 U11 RESET PICS
SC1
C29
REG1 REG2 REG3 U12 LED7
SWIN STAT
SR2
POWER
U15 U16 C48
U13 U14
U17 U18 L2
C40
C47
BR1
U19 U20
ANALOG INPUTS TB3 TB4 DIMMING OUTPUTS TB5 SWITCH INPUTS TB6 TB2 LSO TEST TB7
C49
LOCAL J7 J8
AN AN AN AN IN IN LS IN IN LS IN IN LS IN IN LS
1 2 3 4 ANALOG COM VIO 1 GRY 1 VIO 2 2 GRY 3 VIO 3 GRY VIO 4 GRY 4 1 +24 2 1 3 +24 4 2 5 +24 6 3 7 +24 8 4 +24 GND C39 REMOTE
TP1