Cooper Greengate LiteKeeper Serie Manual De Instrucciones

Installation Instructions
LiteKeeper® Logic Board (16/32)
Carte logique LiteKeeper® (16/32)
Placa lógica LiteKeeper® (16/32)
General Information
The LiteKeeper® Logic Board is shipped separately
from the enclosure to protect the components during
shipping and enclosure installation. Enclosure installation
instructions have been provided for the enclosure.
Please refer to the enclosure installation instructions
for instructions on mounting the enclosure as well as
wiring loads to the relays. This document discusses
the mounting and connection of the LiteKeeper® into
the enclosure and assumes that this step has been
completed.
Getting Started
1. Do not discard these installation instructions. Please
keep for future reference and operation information.
2. It is recommended that all low voltage wiring be
done with power removed to the logic board to
protect components from potential shorts during the
wiring process.
3. Use only as intended and at the listed voltage.
4. All installation and service must be performed by
qualified personnel or service technicians.
5. Install in accordance with the National Electrical Code
and any other codes which may apply.
6. Installation and wiring information contained in this
document is based on industry-accepted standards
and practices. If conflicts exist between these
instructions and any applicable codes or ordinances,
please contact Greengate before proceeding with
the installation.
7 . High Voltage is present inside the enclosure. Use
extreme caution when performing maintenance on
this equipment. Failure to follow this warning and
proper safety procedures could result in severe injury
or death, and/or damage to the equipment.
Model # LK LB
8. Document all wiring and device terminations and
locations so that devices can be properly configured
and programmed for operation.
Mounting in the Enclosure
The enclosure should have been mounted prior using the
installation instructions provided for this purpose. It is
recommended that the LiteKeeper® not be put into the
enclosure until all drilling is complete in the cabinet.
J1
P1
L3
POWER
L4 L5
L21
STATUS
L22 L23
1 2 3 A
4 5 6 B
7 8 9 C
* 0 # D
ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24
VDC VDC VDC VDC VDC
CH17 CH18 CH19 CH20 CH21
CH1 CH2 CH3 CH4 CH5
ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24
VDC VDC VDC VDC VDC
TB2
16 size Enclosure with LK Mounted
1. Remove all debris and metal shavings from
the enclosure.
2. Make certain that there is no high voltage wiring
exposed or in the space of the low voltage section of
the enclosure.
INS #
CAN CAN
TX RX
BLUE
L1
L2
RED
L6 L7 L8 L11 L12 L13 L14 L15 L16 L17 L18 L19
L9 L10
L25 L26 L27 L29 L31 L33 L36 L37
L24 L28 L30 L32 L34 L35
J4
OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF
VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC
CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 CH32 J5
J6
CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF ON +24 OFF TB3
REMOTE PWR
VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC
+24 GND