Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Introduction
The LiftMaster
®
Retro-Refl ective Photoelectric
Sensor provides non-contact monitored entrapment
protection. For use with LiftMaster
gate operators. The sensor is a UL Recognized
Component and meets UL 325 requirements.
Monitored external entrapment protection devices
MUST be installed at each Entrapment Zone. Refer to
gate operator manual for compatibility with LMRRUL
sensor.
Specifi cations
Max Range: 50 ft. (15.2 m)
Sensor Dimensions with Hood:
2.29" W x 3.72" H x 2.76" D
Refl ector Dimensions with Hood:
2.61" W x 4.72" H x 2" D
Cable Length: 10 ft. (3 m)
Operating Temperature: -40˚C to 65˚C
(-40˚F a 149˚F)
Outdoor Rating: Nema 4X
To prevent possible SERIOUS INJURY or DEATH from a closing gate or door:
Read and follow ALL instructions.
Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the photoelectric sensor.
The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster
Monitored Entrapment Protection device.
Correctly connect and align the photoelectric sensor.
Install the photoelectric sensor so that the center of the sensor window is NO HIGHER than 4-3/4"
(12.1 cm) above the fl oor for door operators and 26" (66 cm) above grade for gate operators.
Monitored external entrapment protection devices MUST be installed per the operator installation
manual at each Entrapment Zone.
The sensor and refl ector MUST be mounted vertically.
Use the provided refl ector ONLY.
Test the gate operator and ALL photoelectric sensors monthly. Replace ANY damaged devices.
SAVE THESE INSTRUCTIONS.
WARNING: This product can expose you to chemicals including lead, which are known
to the State of California to cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
MONITORED RETRO-REFLECTIVE
®
UL Listed
PHOTOELECTRIC SENSOR
Input voltage:
Sensor: Black/red wires 6.8 VDC, 20mA
Heater: Green/white wires 10-40VDC or 8-28 VAC, 2
watts max., 170mA @ 12 VDC/VAC,
85mA @ 24 VDC/VAC
Heater: Thermostatically controlled, NOT
recommended for solar applications
Model LMRRUL
®

Publicidad

Tabla de contenido
loading

Resumen de contenidos para LiftMaster LMRRUL

  • Página 9: Introducción

    Asegúrese de DESCONECTAR TODO SUMINISTRO DE ENERGÍA del operador ANTES de instalar el sensor fotoeléctrico. • La puerta o portón DEBE estar en posición totalmente abierta o cerrada ANTES de instalar el dispositivo de protección contra atrapamiento monitoreado LiftMaster ® • Conecte correctamente y alinee el sensor fotoeléctrico.
  • Página 10: Contenido De La Caja

    Contenido de la caja Herramientas necesarias • Sensor fotoeléctrico con • Tornillo de bloqueo roscado campana y ménsula 10-32x1 pulg. (2) • Destornillador estrella • Refl ector con campana y • Tornillos de 1/4 pulg.-20 x • 1/8 pulg. Llave Allen ménsula 1-1/4 pulg.
  • Página 11 Cableado Cableado del sensor: Conecte el sensor fotoeléctrico (cables rojo [+] y negro [-]) al operador como se muestra. Cableado del calentador: El calentador (cables verde y blanco) puede alimentarse de una de estas dos maneras: • Conecte al terminal ACCESORIO DE ENCENDIDO en el tablero de control (NO es específi co a la polaridad). •...
  • Página 12: Resolución De Problemas

    • Consultar con el distribuidor o con un técnico de radio/TV establecen para brindar un nivel razonable de protección contra experimentado para pedir ayuda. interferencias perjudiciales en instalaciones residenciales. Este equipo © 2018, LiftMaster All Rights Reserved Tous droits réservés 01-39358 Todos los Derechos Reservados LiftMaster.com...

Tabla de contenido