Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

WARNING
Study, understand and follow all instructions provided
with this product. Read these instructions carefully before
installing, operating, servicing or repairing this tool. Keep
these instructions in a safe accessible place.
INTENDED USE OF THE TOOL
This sander is designed for sanding metal, plastic and
painted surfaces to strip paint for fine finishes. Do not use
this tool outside of the designed intent. Never modify the
tool for any other purpose or use.
WARNING
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using this
product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
MICRO 2" SANDER
- .4HP
The manufacturer warrants this product to the original user against defective
material or workmanship for a period of 1 year from the date of purchase.
The manufacturer reserves the right to determine whether the part or
parts failed because of defective material, workmanship or other causes.
Failures caused by accident, alteration or misuse are not covered by this
warranty.
The manufacturer, at its discretion, will repair or replace product covered
under this warranty free of charge. Repairs or replacements of products covered
under this warranty are warranted for the remainder of the original warranty
period.
The manufacturer or its authorized service representatives must perform
all warranty repairs. Any repair to the product by unauthorized service
representatives voids this warranty. The rights under this warranty are
limited to the original user and may not be transferred to subsequent owners.
The warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular purpose.
Some states do not allow the exclusion or limitations of incidental or
consequential damages, so the above limitations may not apply to you.
Authorized Matco Repair Centers:
United States
Matco Air Tool Repair SV
1330 Commerce Drive
Stow, OH 44224
(800) 433-7098
NMG Industrial WTRC
Attn: South Dock
2223 S. Wilson Street
Tempe, AZ 85282
PRODUCT INFORMATION:
• Ultimate customization. Adjust running speed from
7,000-19,000 RPM and pad size from 2" to 3".
• Compact profile. Extremely short length of just 3.3".
• Unmatched power. .4 HP that won't bog down during
use.
SPECIFICATIONS:
Pad Size: 2" & 3"
Spindle: 5/16"-24 (Female)
Free Speed: 7,000~19,000 RPM
Air Consumption: 3.1 CFM
Air Inlet: 1/4"
DO NOT DISCARD – GIVE TO USER
Page 1
MT2420
1 YEAR LIMITED WARRANTY
Canada
H. T. Pneumatic Rebuilders Inc.
22 Goodmark Place
Units 7 & 8
Toronto, Ontario M9W6R2
Made in Taiwan
to Matco specifications
Motor: .4 HP
Pressure: 90psi
Exhaust: Side
Weight: 1.1 lbs.
Length: 3.3"
1512184-14

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Matco Tools MT2420

  • Página 1 MICRO 2" SANDER MT2420 - .4HP WARNING Study, understand and follow all instructions provided with this product. Read these instructions carefully before installing, operating, servicing or repairing this tool. Keep these instructions in a safe accessible place. Made in Taiwan to Matco specifications...
  • Página 2 5.) ORDERING SERVICE PARTS: For further operational and handling information or for replacement of parts and components, contact your Matco Tools Distributor. *When ordering parts and components, give each part number, name and quantities. Page 2...
  • Página 3: Cautions For Use

    MICRO 2" SANDER MT2420 - .4HP WARNING CAUTIONS FOR USE 1) This tool is intended for polishing and sanding with all Users of this tool should review the chemical composition of types of movement e.g. rotary, orbital and reciprocat- the work surface and any products used in conjunction with...
  • Página 4: Aplicación De La Herramienta

    LIJADORA MICRO MT2420 DE 2" Y 4HP ADVERTENCIA Estudie, entienda y siga todas las instrucciones que se proveen con este producto. Lea las instrucciones detenidamente antes de instalar, operar, dar servicio o reparar esta herramienta. Guarde estas instrucciones en un lugar seguro HECHO en Taiwán...
  • Página 5 LIJADORA MICRO MT2420 DE 2" Y 4HP ADVERTENCIA INSTRUCCIONES DE MANTENIMIENTO: 1.) Lubricación: 1) La herramienta no serán utilizados en atmósferas Antes conexión de la manguera, se aplican de 4 a 5 gotas potencialmente explosivas. de una buena calidad del aire herramienta de petróleo en la entrada de aire.
  • Página 6: Precauciones En Uso

    LIJADORA MICRO MT2420 DE 2" Y 4HP ADVERTENCIA PRECAUCIONES EN USO Los usuarios de esta herramienta debe examinar la composición 1) Esta herramienta se destina vaivén de lijado y pulido con todos química de la superficie de trabajo y cualquiera de los productos los tipos de movimiento, por ejemplo rotativo, orbital y alternati utilizados en conjunción con esta herramienta para cualquiera de esos...
  • Página 7 MT2420 MICRO PONCEUSE DE 2" AVERTISSEMENT Etudier, comprendre et suivre toutes les instructions fournies avec ce produit. Lire ces instructions attentivement avant d’installer, d’utiliser, d’entretenir et de réparer cet outil. Fabriqué à Taïwan Conserver ces instructions dans un endroit les spécifications de Matco sécuritaire et accessible.
  • Página 8: Instructions D'entretien

    Pour de plus amples informations sur le maniement, ou pour le remplacement de pièces et composants, contactez votre Distributeur de Matco Tools. ** Lors de la commande de pièces et composants, donner à chacun le numéro, le nom et les quantités.**...
  • Página 9 MT2420 MICRO PONCEUSE DE 2" AVERTISSEMENT MISES EN GARDE CONCERNANT L’UTILISATION DE CET OUTIL L'utilisateur de cet outil devrait s'informer sur l'existence de tels produits chimiques dans la composition chimique de la zone de 1) Cet outil est destiné au polissage et au ponçage utilisant tout travail et des produits utilisés conjointement avec cet outil avant de...
  • Página 10 MICRO 2" SANDER MT2420 - .4HP PARTS BREAKDOWN Parts List Ind e x P ar t No . D es cr ip tio n Qty . Index P a r t No . D e sc r ip t io n Qt y .

Tabla de contenido