Troubleshooting; Correct Disposal Of This Product - Eye-Vac Home Manual Del Usuario

English
CLEANING THE MICRO EXHAUST FILTER HOLDER
1. The Micro Exhaust Filter Holder slides up and out of its housing on the side of the unit.
2. Gently pull the Filter out of the Filter Holder. (See Figure 4)
3. Tap Filter gently against trash container to free and eliminate excess dirt and debris. (See Figure 5)
4. To clean the Filter, wash in mild soap and water; rinse and dry thoroughly before using the unit.
5. If a new Filter is needed, replace with standard HEPA HF4 filter cartridges. Make sure that it fits snugly in the Filter
Holder. Replacement Filters are available through the Customer Service Department.
6. Slide the Holder back into the unit with the Filter facing outwards.
IMPORTANT! NEVER OPERATE EYE-VAC HOME WITHOUT THE MICRO EXHAUST FILTER AND FILTER HOLDER
PROPERLY IN PLACE.
The Collection Bin should be washed periodically.
1. Wash the Bin in warm water using a mild soap. Avoid harsh or abrasive cleaners or sponges. Rinse thoroughly.
TO AVOID DAMAGE, DO NOT PLACE COLLECTION BIN IN THE DISHWASHER.
2. Let it air dry. Make sure the Collection Bin is completely dry before putting it back into the EYE-VAC PROFES-
SIONAL.
3. Insert the assembled Collection Bin following the instructions outlined in the USER MAINTENANCE
INSTRUCTIONS on page 3.
IMPORTANT NOTES
Other than cleaning the Dirt Filter and replacing the Micro Exhaust Filter Holder, as described in this
this Automatic Vacuuming Dust Bin is not user serviceable. There are no user serviceable parts inside the unit.
Servicing by our Authorized Service Center is required to avoid damage to internal components.
1. Unplug unit and clean Collection Bin and all Filters before storing.
2. Store EYE-VAC HOME indoors, in a clean, dry place.
3. Never store EYE-VAC HOME while it is still plugged in. Never wrap cord tightly around the appliance, use the Cord
Storage area on the back of the EYE-VAC HOME unit. Do not put any stress on the cord where it enters the unit, as it
could cause the cord to wear and break.
WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT USE OUTDOORS OR ON WET SURFACES.
Problem
EYE-VAC HOME
won't run
Does not pick up debris
1.Dirt inlet is blocked 2.Container
is full 3.Debris may be too large
for inlet
EYE-VAC sensors do not activate 1.Unit is not in AUTO mode
1.Filters may be dirty
Suction is not strong
Status indicator light blinking
Collection Bin Indicator Light is
1.Collection bin is full
ON
Debris at inlet before unit is
powered on

Correct Disposal of this product

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environmental safe recycling.
CLEANING THE COLLECTION BIN
STORAGE
TROUBLE SHOOTING
Possible cause Possible Solution
1.Not firmly plugged in 2.Unit is
1.Plug in firmly 2.Depress Power Button to MAN or
in OFF position 3.Dirt filter is not
AUTO position 3.Re-attach collection bin lid to top of
in position 4.No power in wall collection bin 4.Check house fuse or circuit breaker
plug 5.Blown house fuse or
5.Have a qualified licensed electrician replace house fuse
tripped circuit breaker
or reset circuit breaker
First. Depress Power Button to OFF position 1.Clean
path of dirt inlet 2.Empty collection bin 3.Clear large
debris
1.Depress Power Button to AUTO position
1. Depress Power Button to the OFF position 2. Clean
Dirt filter or Micro Exhaust filters when needed.
1.Eye-Vac sensors have been shut 1. Depress Power Button to the OFF position
off for 30 seconds which caused
2.Check dirt filter and micro exhaust filters to
power to the motor to be shut off ensure they are clean.
1. Empty the Collection Bin; 2.Clean all dirt filters
1.Depress Power Button to the MANUAL position
2.Activate unit manually
s Manual,